Given that → = 50 deg, P₁ = 200 lb, and P₂ = 150 lb, determine the following: a) x and y components of P1 b) parallel and perpendicular components of P₂ along rod AB c) parallel and perpendicular components of 300 lb along rod AB P₁ 30° d) parallel and perpendicular components of 50 lb along rod AB . Resolve the following into x and y components given that 300 lb 50 lb B P₂ x

Given that → = 50 deg, P₁ = 200 lb, and P₂ = 150 lb, determine the following: a) x and y components of P1 b) parallel and perpendicular components of P₂ along rod AB c) parallel and perpendicular components of 300 lb along rod AB P₁ 30° d) parallel and perpendicular components of 50 lb along rod AB . Resolve the following into x and y components given that 300 lb 50 lb B P₂ x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the vertical displacement B of joint B of the truss shown in Figure, Note that the only load acting on the truss is a vertical load Pat joint B. Assume that both members of the truss have the same axial rigidity and cross-sectional area. A = 600 mm², E = 200 GPa 45⁰ B 45⁰ 50 KN 1.5 m
Analyze the truss completely by method of joints. Make a summary of your answers by creating a table ordered as shown below. F=10KN.
Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm2 , E1=E2= 100 GPa , a1=a2= 12x10/°C, AT= -25 °C, h= 1700 mm, 0 = 65° (1) (2) h B
The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross- sectional area of 25 mm' and a =11.7 *10 m/ m°C. 15 KN 0.2 m 0.2 m 0.4 m
Solve using FEM stepwise O 4,E 2 2 P L Problem: Determine the support reaction forces at the two ends of the bar shown above, given the following, P = 6.0 x 10ʻ N, E = 2.0 × 10* N / mm', A = 250 mm², L=150mm, A=l.2 mm
J 6
Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa, a1=a2= 12x10/°C, AT= 35 °C , h= 1200 mm, 0= 60° (1) (2) B
SITC. Determine the horizontal displacement (mm) of joint C. 300 lb 300 lb 13 ft B 5 ft 12 ft 13 ft 12 ft
For all bars L = 5 m, A = 20 mm^2, E = 210 GPa, I = 166 mm^4. Determine deformed shape. Determine node reactions.
Determine the magnitude of force (lb) in member BD if P = 166 lb, x = 16.8 in, y = 10.3 in, and z = 10 in. Round off only on the final answer expressed in 3 decimal places.
A cantilever beam has a span of 3 m. The beam carries a uniform service load w = 22 kN/m includes the weight of the beam. There is no lateral support other than that at the fixed end. 258.83 P }22.10 w = 22 kN/m K 38.1 d= 269.24 1.5 m. (K = 38.1 122.10 3 m. Properties of W 10 x 77 A = 14581 mm2 Lp = 2.799 m d = 269.24 mm L, = 13.811 m bf = 258.83 mm Lp = 3 m %3D tf = 22.10 mm Fy = 345 MPa tw = 13.46 mm K = 38.10 mm Sx = 1408 x 103 mm3 E 3 200,000 MРа Zx = 1599 x 103 mm3 a. Determine the value if the service load P due to the max. shear strength of the beam using LRFD. b. Determine the value if the service load P due to the max. shear strength of the beam using ASD. c. Determine the value of the service load P due to the flexural strength of the beam using LRFD. d. Determine the value of the service load P due to the allowable bending strength of the beam using ASD.
2. A two-member truss structure is loaded as shown. Determine the horizontal and vertical components of the displacement of point A. CY dimensions in meters TAB 3 A 80KN 4:5 EAB 70 GPa ; EAC=70 GPa AAB=150mm²; AAC = 100mm²