Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of o.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1-in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 13-in. pipe to a 2}-in pipe.

Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of o.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1-in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 13-in. pipe to a 2}-in pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water…

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: e height of the water

Q: You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to…

A: A pitot tube is a device that consists of a tube with a brief right-angled bend that is…

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: Based on the layout of the water supply system, how much pressure in psi will be available at the…

A: Given:Pressure at the source, P1=75 psi=75*144 lb/ft2=10800 lb/ft2Water flow rate, Q=3.75 cfsPipe…

Q: 4. A special oil is to be used in an absorption tower. The preliminary design of the unit requires…

A: A schematic diagram of the given case is Given data, Datum height at section 1, Z1 = 10 ft Length…

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at…

Q: Figure 1 shows water at 20°C to be circulated from and to the reservoir. The 30 diameter pipe made…

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa dA=150mm PB=325KPa dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of…

Q: Crude oil having a specific gravity of 0.93 and a viscosity of 4cP is draining by gravity from the…

A: Given, Specific Gravity = 0.93 Coefficient of viscosing is = 4cp = 4 x 10-2 poise = 4 x 10-3 pas…

Q: Assemble and describe the operation of a simple piping system (with only one branch, or at most two…

A: Firstly, we need to assemble the piping system. The main pipe will start from the pump, which is…

Q: Problem 3: A submersible deep-well pump delivers 745 gal/ h of water through a 1-in Schedule 40 pipe…

A: Given Data The flow rate of water is:Q=745 gal/h=0.0276644 ft3/s The head loss in pipe is:hL=10.5…

Q: Benzene at 37.8 °C is pumped through the system of Figure at the rate of 0.1515 m³/min. The…

A: Given data Benzene temperature = 37.8 °C pumped at the rate = 0.1515 m³/min.. The gauge pressure…

Q: Determine the loss of pressure in overcoming the friction in a coil through which water flows with a…

A: Given information: velocity = 1.2 m/s internal diameter of pipe = 30 mm = 0.03 m Since 10 turns,…

Q: 0 oil volume flow rate

A: given:

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required pump power.

Question

Mechanical-Energy Balance and Friction Losses. Hot water is being discharged
from a storage tank at the rate of o.223 ft3/s. The process flow diagram and
conditions are the same as given in Example 2.10-6, except for different nominal
pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from
the storage tank is 1-in. pipe instead of 4-in. pipe. The other piping, which was
2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after
the elbow in the 13-in. pipe to a 2}-in pipe.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Calculation:

Figure:

Calculation:

Calculation:

Calculation:

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (2) Select the correct simplified general energy equation for point 1 and 2
Problem #4 If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes are galvanized iron with 0.0005 ft. Take v = 1.06 × 10−5 ft²/s and neglect Kis = minor losses. 10 in. dia 1. 2000 ft, 8 in. dia A B 1600 ft, 6 in. dia с 2. 800 ft, 10 in. dia-
5. The water in the right figure is flowing steadily. What is the flow rate? 10 ft 10 ft Y Very large Water 3-in steel pipe
Water at 100°F is flowing through a straight 4-in schedule 40 pipe at a rate of 1 gal/min. The length of the pipe is 10 ft, find the velocity at the center of the pipe in feet per second?A. 0.0378B. 0.0504C. 0.0454D. 0.0252
Don't use chatgpt. I need right answer.
The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow the suggested design procedure and select a suitable pipe size and pump for the system. A B A: Globe valves (2 of them) B: Union fittings (4 with 2 not shown) C: Plate welded to tank to suppress air entrainment in pump inlet D: Elbows: there are five 90° elbows and two 45° elbows The pipe is all wrought iron, with threaded fittings, schedule 40. Pipe lengths total 35.36 m. Total inlet pipe length from tank to pump is 1.22 m. z1 = 1.22 m and z2 = 3.66 m.
Problem 2. Water at 150°F is pumped at the rate of 60 gal/min from a reservoir at atmospheric pressure. The gauge pressure at the end of the discharge line is 42 psi. The discharge point is 12 ft above the level is the reservoir and the suction line is 6 ft above the level of the reservoir. The discharge line is a 1 ½ in. nominal dimeter steel pipe with a schedule number of 80. The pressure drop due to friction in the suction line is known to be 0.8 psi, and that in the discharge line is 7.2 psi. The mechanical efficiency of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c) If the pump manufacturer specifies a required NPSH of 8 ft, will the pump be suitable for this service?
Example Problem The fluid being pumped is oil with a specific gravity of 0.86. Calculate the energy delivered by the pump to the oil per unit weight of oil flowing in the system. Energy losses in the system are caused by check valve and friction losses as the fluid flows through the piping. The magnitude of such losses has been determined to be 1.86 N.m/N. Pump system. The volume flow rate through the pump shown in figure below is 0.014 m³/s. SOLUTION: +EO PB = 296 kPa Schedule 40 (From Pipe Supplier's Table) Wall Flow Area ao NO ao Thickness DN 50 Schedule 40 (ww) 0.002163 steel pipe 60.3 3.91 52.48 88.9 5.49 77.92 0.004768 08 GENERAL ENERGY EQUATION BETWEEN POINTS A & B: Flow PA/y + Z, + v/2g +h- hg -h = PB/y+ ZB + Vp²/2g 1.0 m %3D Therefore, Ty + 87/(A -A) + ("z - "z ) + ^/(°d - d) = 'y DN 80 Schedule 40 %3D Check valve From continuity equation, v = Q/A, find VA & VB VA = ? steel pipe PA =-28 kPa %3D Vs = ? Pump CHECK ANSWER h =42.9 m, or 42.9 N.m/N %3D 5.
Pressure difference required for pipe with elevation change. Water at 68°F is to be pumped through 95 ft of standard 3-in. pipe (internal diameter 3.068 in.) into an overhead reservoir as illustrated in Fig. 6A.2. 30'- Fig. 6A.2 Pipe flow system. 45° elbow 45° elbow Pump 50 45° 15'- (a) What pressure is required at the outlet of the pump to supply water to the overhead reser- voir at a rate of 18 gal/min? At 68°F the viscosity of water is 1.002 cp and the density is 0.9982 g/ml. (b) What percentage of the pressure drop (pump outlet to reservoir) is needed for overcoming the pipe friction? Answer: (a) 15.3 psig
2. Water steadily flows from the basement to the second floor through a 0.75-in-diameter copper pipe. The volume flow rate is constant as Q = 12 gal/min (gpm). Water exits through a faucet having a diameter of 0.5 in. Consider all losses, and determine the pressure at (1) required to maintain the constant volume flow rate. If needed, use the tables below and the Moody chart on the last page. Water has a density of 1.94 slug/ft3 and a viscosity of 2.34 x 10-5 psf s, and the gravitational acceleration is g = 32.2 ft/s². The following conversion relations can be used: 1 ft = 12 in, 1 gal = 0.160544 ft³. KL 0.6 0.4 0.2 0 Q-12 gpm Copper Commercial steel or wrought iron 0.2 Pipe Riveted steel Cast iron A₁ 0.4 (1) A₂/A₁ 0.75-in-diameter copper pipe 0.6 15 ft 10 ft A 0.8 (6) 5 ft (3) 1.0 (5) 10 ft 10 ft (7) (8) •∞• 10 ft 8 Threaded 90 elbows Loss coefficients for pipe components KL Elbow, regular 90°, flanged 0.3 Tee, flanged 1.0 Faucet 2.0 0.05 10 0.15 2 1.5 Ball valve, fully open Globe,…
Parvinbhai
A 10,000-gallon water tank atop a building delivers fresh drinking water for itsoccupants. A top-floor resident and a bottom-floor resident are filling their bathtubs.Assuming frictionless pipes and isothermal flow, which one will fill faster?A. top floorB. bottom floorC. the tubs will fill at the same rateD. need more information