4. A special oil is to be used in an absorption tower. The preliminary design of the unit requires the oil to be pumped from an open tank with a 10 ft liquid level above the floor and forced through 150 ft of 3 inches schedule 40 pipe with a ball check valve and 5 elbows into the top of a tower 30 ft above the floor. The operating pressure in the tower is to be 52 psig and the oil requirement is estimated at 50 gpm. The viscosity of the oil 15 cP and its density is 53.5 lbm/ft. Assuming the pumping outfit operates with an overall efficiency of 60%, what horsepower input will be required for the pump motor?

4. A special oil is to be used in an absorption tower. The preliminary design of the unit requires the oil to be pumped from an open tank with a 10 ft liquid level above the floor and forced through 150 ft of 3 inches schedule 40 pipe with a ball check valve and 5 elbows into the top of a tower 30 ft above the floor. The operating pressure in the tower is to be 52 psig and the oil requirement is estimated at 50 gpm. The viscosity of the oil 15 cP and its density is 53.5 lbm/ft. Assuming the pumping outfit operates with an overall efficiency of 60%, what horsepower input will be required for the pump motor?

Name: 4. A special oil is to be used in an absorption tower. The preliminar
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4. A special oil is to be used in an absorption tower. The preliminary design of the unitrequires the oil to be pumped from an open tank with a 10 ft liquid level above the floor andforced through 150 ft of 3 inches schedule 40 pipe with a ball chec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

03
Which of the following represent primary losses A. fluid splitting devices B. friction along the bends C. the losses due to area change D. loses in valves E. frictions along the pipe length
What is the minimum duct size needed to move 200 cu ft per minute andmaintain duct velocity below 800 feet per minute?
With the use of suitable schematics, describe how a manometer can be used to measure the pressure in an installed pipeline
The pump generates a 10 bar and the pressure difference across the motor and the flow control valve are 6 bar and 3 bar respectively.Neglecting pressure losses in the pipes ,how much pressure is required in order for the relief valve to open?
Draw and describe a simplified diagram of a section of an industrial sugar and alcohol piping system, which contains the following equipment: 1 Pump 1 Heat Trocador Elbows for changing the flow path Flux Valves The ultimate goal is to calculate system and pump pressure losses.
If the compressor suction pressure is 70 pounds per square inch gaugepressure (psig) and the outside temperature is 85°F, what should thedischarge pressure be reading?
Sometimes pumps do not perform as tested when they are installed in a pipeline. Name and describe four (4) ways in which the pump parameters can be changed in order to meet requirements.
What is the pipe pressure (pa)? Given the S for Mercury is 13 and S for fluid =3.4
Is there a flaw in the pipeline design as shown in Flgure 4 ? (select one): (A) The strainer and foot valve should not be used as the combination may cause cavitation. (B) The foot valve should not be used as it may cause cavitation. (C) The pump should be placed at a higher elevation to prevent cavitation from occurring. (D) The gate valve should not be placed on the suction side of the pump as it may cause cavitation. (E) The intake is not placed deep enough below the water surface of the river as it may cause cavitation. (F) None Elevation 180 m- 450 All of Steel Pipe Diameter 250mm· Smooth Bend B Gate Valve- (wide open) River Elevation -Pump at Elevation 125 m 120 m Smooth Bend Sump -Strainer and foot valve at 115m Figure 4
Indicate how velocity, water temperature, and pipe area affect the Reynolds number.