Pressure difference required for pipe with elevation change. Water at 68°F is to be pumpedthrough 95 ft of standard 3-in. pipe (internal diameter 3.068 in.) into an overhead reservoir asillustrated in Fig. 6A.2.30'-Fig. 6A.2 Pipe flow system.45° elbow45° elbowPump5045°15'-(a) What pressure is required at the outlet of the pump to supply water to the overhead reser-voir at a rate of 18 gal/min? At 68°F the viscosity of water is 1.002 cp and the density is0.9982 g/ml.(b) What percentage of the pressure drop (pump outlet to reservoir) is needed for overcomingthe pipe friction?Answer: (a) 15.3 psig

Pressure difference required for pipe with elevation change. Water at 68°F is to be pumped through 95 ft of standard 3-in. pipe (internal diameter 3.068 in.) into an overhead reservoir as illustrated in Fig. 6A.2. 30'- 6A 2 n:

Pressure difference required for pipe with elevation change. Water at 68°F is to be pumped through 95 ft of standard 3-in. pipe (internal diameter 3.068 in.) into an overhead reservoir as illustrated in Fig. 6A.2. 30'- 6A 2 n:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A cylindrical pipe with water flowing downward at 0.02 m^3/s having top diameter of 0.08m, bottom diameter of 0.04m and height of 1.5m. Find the pressure between the pipe in kPa.
Q2. As a part of an Oil Company's Process Safety plan, crude oil tank fire scenario can be mitigated by pumping the tank empty in 1 hour. The crude oil is at a 9m level, with the tank diameter being 30m. It is planned pump the oil through a 200mm ID new commercial steel pipe (e = 0.046mm) to another tank 40m in diameter and 10m high. The pipeline runs to an equivalent length of 50m. a. In the time mentioned above, what minimum pump size (in HP) would be required to pump the tank empty. Assume pump efficiency of 80%. b. If a 100 HP (80% efficient) pump is available, how long will it take to empty the tank? c. What conclusions can be drawn about the viability of this approach? What kind of hazards can be foreseen in this operation from a process safety perspective? What can be a probable initiating cause of an accident? What can be a suggestion to mitigate the risks? Density: 928 kg/m', Viscosity: 0.004 kg/m-s
Part A plz
Q2: The discharge of water inside the pipe is 1 liter/s, the diameter and roughness of the pipe is 40 mm and 0.045 x 10- m respectively, find the friction factor and the loss of head per meter length pipe? Take p=1000 kg/m', H=I* 10* kg/m.s
The large reservoir in the following figure provides water for the indicated tank with a flow rate of 10 L/s. Check that the machine is installed and a pump or a turbine, and determine its power, if the yield is 75%. Suppose ideal fluid. Data: γH20 = 104N/m3 ; ATubes = 10mc2 ; g = 10m/s2 .
Problem 4 (a) Water from a water reservoir is delivered through a 2-cm pipe to a 200-litre tank as shown in Figure below. The water level (H) is at 2 m above the pipe. Calculate (a) the time it would take to fill the tank and (b) the height difference of the mercury, h in a U-tube manometer. State all assumptions needed. (Non-anonymous questionO) * h H Water Mercury S.G. =13.6 Jet 200-litre Tank
Q2: The maximum flow velocity of water in a pipe is 2.4 m/s . The pipe has 0.2 cm diameter , and 15 m lenghth .Determine the pressure drop of the head loss?. Note, pwater= 1000 kg/m3 , and uwater=1.307 *10° N/m.s.
Water at 25°C is pumped at 1800 gal/min from the lower to upper reservoir, as shown in Figure below (Zı = 30 ft and z2 = 180 ft). Pipe friction losses are approximated by hf = 35V/2g, where V is the average velocity in the pipe. The pump is 80% efficient. (a) Find the head loss due to friction, hẹ in ft. in horse power (b) Compute the pump head, h, in ft and the pump power needed, Ppump (hp). Given: Specific weight of water, ywater = 62.4 lb/ft'; 1 ft/s = 448.8 gal/min. Show all calculations. Z2 = 180 ft Z¡ = 30 ft D= 6 in Pump
2. Oil with a S.G. pf 0.82 is flowing in a pipe under the condition below (see figure). If the total head loss from point 1 to point 2 is 3 ft, find the pressure at point 2 in PSI. Note: cfs = cubic ft per sec Point 1 D₁ - 6 km P₁-65 pal 0 Q-2.08 efs Q-2.08 efs Point 2 D₂ - 9 in 10.70 ft 4.00 ft Reference datum
B4. An orifice meter with orifice area 1072 mm2 is inserted in a pipe of area 2144 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.85 when the co-efficient of discharge of the orifice meter = 0.6. Head of water (in m) The discharge of water through pipe (in Litres/sec)
60 deg F engine oil flows in a 6" diameter pipe of length 13 feet. The gage pressure at the pipe inlet is 1 psi; the oil exits the pipe to the atmosphere. Determine the volume flow rate of the oil in ft3/sec. You can assume laminar flow.