Determine the loss of pressure in overcoming the friction in a coil through which water flows with a velocity of 1.2 m/s. The coil is made of used steel pipe with an internal diameter of 30 mm. The diameter of the coil is 1m. The number of turns is 10. The average temperature of water in the coil is 30°C.

Q: Solve the following equation for the value(s) of VAR. Round your answer(s) to 2 decimal places and…

A: Given   Equation        5 VAR2 + 6 VAR - 18 = 0 Where, take a = 5                    b = 6…

Q: I need help solving problems 7, 8, and 9 pertaining to the print attached below.

A: 7.In question no. 7 information is not enough to answer the question. As there are many circles in…

Q: Using the graphical method, find the sum of the vectors in each number. Draw your vectors on a…

A: The given data in the problem is listed in the following attached image:

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: An airplane flies at 28.9 m/s. The engine thrust exactly balances the drag force, which is 7.3 N.…

A:

Q: Could ypu help me with this problem? It should start with something like this: P1=0,0 P2=10,0…

A: The part program for the given drawing uses the Fanuc Cut language. I'll start by identifying key…

Q: Suppose a dimension is indicated on an engineering drawing (with all units in inches) as 1.658 ±…

A: The lower limit of dimension= 1.658 - 0.008 = 1.650 Option third is correct.    Similarly, we can…

Q: 0.2 m B 0.2 m 1.3 m 0.7 m A P Circular

A:

Q: Please walk me through finding how much force the women need to pull the force

A: Given data: Weight is W Need to determine the required force to pull the weight.

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: The piston displacement of an air compressor is 1200 liters per minute. Its bore and stroke are 12…

A:

Q: You are in an inventory management field these days.  You are working for a place which works on 365…

A: The objective of this question is to determine the number of orders per year that should be placed…

Q: A. Find the value of tapered angle (a): Answer:

A: Find    The value of Taper angle

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&T symbols used in the image:Datum symbols: A datum is a…

Q: A person is pulled to the right on a sled (total mass of 53.3 kg) across the surface of a frozen…

A:

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Given Data: The given number is N = 826.48 The number should have three significant figures, hence…

Q: Can you help me with this problem? P1 is where the blue dot is

A: 1. N10 G90 - Set to absolute positioning.2. N20 G54 - Select the work coordinate system.3. N30 G00…

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Q: In an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A:

Q: The solar energy can generate 1.5 kW per one square meter of a solar collector with a total area of…

A:

Q: Can you write me a program manuscript using geometric definition on FAPT language. The starting…

A: To create a part program for the given part drawing (Fig. 2) for a wire electric discharge machine…

Q: A car drives on a circular track with radius 220 m. Initially, the displacement s=0 and the speed is…

A: Given data: Radius  R=220 m displacement s=0 speed u=17 m/s at=0.1s m/s2 t=2.1 sec

Q: A motorcyclist left from his work at 5:45 in the morning and arrived at the coffee shop 42 km away…

A:

Q: A fire tube boiler develops 75 metric tons of steam at a pressure of 12.5 mpa and a temperature of…

A:

Q: From the figure shown. To determine: a) Piston force BC b) Piston force FE c) Pin force G and J d)…

A: Consider the free body diagram of bucket is shown below, Taking moment about point J, ∑MJ=020000…

Q: c 2. How much money will be accumulated in 20 years from a deposit of $1500 every 6 months if the…

A: Years=20Deposit= $1500 every 6 monthInterest rate= 2.75% per monthEquations given:

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: During a steady flow process, the pressure of the working substance drops from 1,380 kpa to 138 kpa,…

A: The work is 2.3207 kW.

Q: A cube has a volume s³. If the edge length is initially 4.20 inches, and the cube is heated such…

A:

Q: SIETER OF THE =::=:: 1575) 조선왕료 foll ROLLO moros.biqui FOR-ONER/STANE POL SAM FOR / TOT Roug 0 2 규…

A: The number of pieces in the given image

Q: Completely solve and box the final answer. Please show the units to show the unit cancellations.…

A:

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: You are in an inventory management field these days. You are working for a place which works on 365…

A: The objective of this question is to determine the number of orders per year that should be placed…

Q: Bar AB has an angular velocity AB = 7 rad/s Part A Determine the velocity of the sider block Cat the…

A: Given:BC = 350 mmAB = 500 mm or 0.5 m/s90° - 60° = 30°45°7 rad/sRequired:VC ( velocity of slider…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.