is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * 30

is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine the shear stress in the 1 inch diameter pin at A which is in double shear: Calculate your answer to 1 decimal place. 7' 5' B W lb/in².
1-41.M A shelf is being designed to hold crates having a to- tal mass of 1840 kg. Two support rods like those shown in Figure P1-41 hold the shelf. Each rod has a diameter of 12.0 mm. Assume that the center of grav- ity of the crates is at the middle of the shelf. Compute the stress in the middle portion of the rods. 1840 kg -600 mm Support rods (2) 30% 1200 mm Shelf
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress s limited to 5000 psi. Assume single shear. 4R + 3t
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5205 lb. Round off the final answer to two decimal places.
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
Consider the contruction shown. Suppose that P₁ = 18 kN and P₂ = 9 kN. Determine the maximum average shear stress developed in each 12 mm diameter bolt. Express the answer to three significant figures and include the appropriate units. | P₁ P₂
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 56 MPa in the shafts and 22 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
ABO(sub1) and BCO(sub2) is a quarter circle with the given dimensions. Let R(sub1) equals to 10 inches. If the section is constant and has a length of 5 ft., The shear load P is acting on the centroidal position from the spar web. Determine the shearing stresses developed in the nose skin and spar web, shear center and the angle of twist. Let G = 4 x 10^6 psi. The thicknesses as follows, for nose skin = 0.080in, for sparweb = 0.10in. -What is the angle of twist? -What is the shear center? hef = 3R1 = 30in P = 6000lbs A %3D F 2R1 02 В 01 R1 D E 4R = = 40in
The two pieces of wood, 2.59in. by 5.69 in., are glued together along the 60°joint. Determine the normal stress (in psi) in the glue if the shear stress in the glue is limited to 352 psi. Round off the final answer to three decimal places. 017 shear.png ... P A
Joints B and D use a pin with a diameter of ø10 mm. In connection C, the diameter of the pin is ø6 mm. The permissible shear stress τmax of the pins is 75 MPa and the permissible normal stress σmax of the rod BD is 200 MPa. Determine the maximum allowable value of the force P. Units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer! Dimension L = 250 mm