A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitud are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c = 5 in. Determine the normal and shear stresse on the outer surface of the pipe at point H and show these stresses on a stress element. b Pz Py

A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitud are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c = 5 in. Determine the normal and shear stresse on the outer surface of the pipe at point H and show these stresses on a stress element. b Pz Py

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 570 mm, b = 285 mm, h = 360 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h B a Answer: Pmax i b kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500 mm, b = 250 mm, h = 330 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a i ● 1.418 B ● ● b kN
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
2. A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure. Determine and draw the state of stresses in small infinitesimal cubic elements located at points M and N on the cross section A. M 0.25 m 50 kNA 0.75 m 100 kN
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
State of stress at the wall and the roof of the following circular opening bafore the excavation is (a] = |0 4. Find the induced stress components at point a. R W with respect to the given x-y coordinate systerm, and expresst them in the matrix form. b. Find the total stresses at point W, and give them in matrix form. c. Repeat (a) and (b) for the roof. d. Find the stresses oy, Ciy, and tyy at point A which is located at a radial distance twice the radius of the tunnel.
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. | Yo B b3 Lütfen birini seçin: a. -155.971 MPa b. -200.302 MPa c. None d. -520.946 MPa e. -124.141 MPa
6. The figure below shows the geometry and loading of segment of a crankshaft. The diameter of the upper shaft is 20mm. Determine the principal stresses and the maximum shear stress at point A, which is located on the surface of the upper shaft at the zo axis. b-80 mm Xo bz = 120 mm by- 40 mm P-LOKN
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of interest A (at the top), B (at the center), and C (midway between A and B). 200 mm where F= 1.4 kN F B 50 mm 50 mm Cross section at wall NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
PROBLEM 3. The stress condition at one point in the tail region of the National Combat Aircraft is shown in the figure. (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point. 40 MPa TAI 200 MPa 80 MPa