g= 105 MPa Daboost/Shutterstock.com

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

A:

Q: A roadway sign weighs 5.4 kN and is supported by a structural pipe that has an outside diameter of…

A:

Q: P=900 KPa, as shown below, is considered. The plate thickness is h-a plate radius is RO=920 mm. If…

A: Pressure = P = 9000 kPaPlate thickness h = 8mmRadius of plate = 920 mmYoung's Modulus = 80 GPa…

Q: A flexible connection consisting of rubber pads(thickness t =9 mm) bonded to steel plates is shown…

A: Given   Force P =16 kN Shear modulus for the rubber is G = 1250 kPa Thickness t =9 mm Find…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 3700 psi, Sy =…

A: Find angle with vertical  to find the normal and shear stress at the given plane, θ= 90 - β= 90-49=…

Q: (a) the principal stresses and the positions of the plane on which they act (b) the position of the…

A: here all angle measure from vertical plane and in counter clock wise direction, if in calculation…

Q: L₁ Rigid bar ABCD is supported by two bars as shown. There is no strain in the vertical bars before…

A: Calculate the contraction in bar (2).

Q: A structural member is subjected to a plane stress loading condition. The state of stress at a point…

A:

Q: The carrier plate in the figure is attached to the column with the help of 3 bolts. A vertical force…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A:

Q: Force is applied to the pipe using a wrench as shown in the figure. The inner radius of the pipe is…

A: Given Data: Inner radius of Pipe ri=75 mm=0.075 m Outer radius of Pipe ro=100 mm=0.1 m Yield stress…

Q: F = 50 kN P P' Area A

A:

Q: The Cartesian components of stress at a point are 0x = 15 Oy = 0₂ = 8, - Txy = 6, Tyz = 4, Txz = 4…

A:

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: Find the normal stress value on the new x-axis obtained by rotating the element with the stress…

A: Write the given data with suitable variables. σx=100 MPaσy=60 MPaζxy=45 MPa

Q: To draw the internal normal force diagram, it is important to determine the internal normal force at…

A: Find internal force at point A Given data:- P1=4.5 kips P2=8 kips

Q: A traffic light and signal pole is subjected tothe weight of each traffic signal WS = 45 lb and…

A:

Q: A thick-walled cylinder with internal and external radii 86 mm and 166 mm respectively, is subject…

A: we have to determine the radial and hoop stress

Q: A rectangular bar having width w = 4.75 in. and thickness t = 2.00 in. is subjected to a tension…

A:

Q: 3) Objects 1 and 2 are positioned as shown in the figure. Object 1 is a rigid support. For object 2,…

A: Consider a body having length L,cross-sectional area A and Young's Modulus E is heated by ΔT°C.…

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: (7) For the state of plane stress shown in the figure, determine the normal and shear stresses…

A: Given data: The stress in the x-direction is σx=-50 MPa The stress in the y-direction is σy=0 MPa…

Q: A circular rod of a diameter of 100 mm is subjected at its free end to force F1 = 50N and F2=(200j -…

A: In this question, three forces are given. The forces are Point force, F1=50i kN Point force,…

Q: A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress…

A: The strain values are given as, ε1=121×10-6ε2=304×10-6ε3=203×10-6 The Poisson's ratio is given…

Q: Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever…

A: The concentrated load, Px = 43 kips, Py = 29 kips, Pz = 52 kipsThe dimensions, a = 7 in, b = 14 in,…

Q: The figure shown is formed by two trusses supporting a block of weight W. The cross-sectional areas…

A: given data cross section area AB=800mm2                                 AC=400mm2allowable stress…

Q: Q2: A rigid platform weighing 53.5 kN is supported by three equally spaced rods. The arrangement is…

A: Write the given data with suitable variables. P=53.5 kN∆T=55.5 °CLs=0.6 mLb=0.9 mEs=210…

Q: A roadway sign weighs 5.3 kN and is supported by a structural pipe that has an outside diameter of…

A:

Q: Parvinbhai

A: Step 1: Step 2: Step 3: Step 4:

Q: In the figure, both ends of the rectangular plate are under the effect of a force p = 150kN. What is…

A:

Q: The stepped shaft shown in the figure is supported by bearings at A and B. Determine the maximum…

A:

Q: Q.1) For the element of material is in biaxial stress with Ox and oy and shear stress Ty, as shown…

A:

Q: The principal plane stresses and associated strains in a plane at a point are s1 = 36 ksi, s2 = 16…

A: Given: The values of principal stresses are s1=36 ksi and s2=16 ksi. The values of strains are…

Q: ABC element with rectangular section shown in the figure is in the (x-z) plane. Find the point at…

A:

Q: σ x and σ y and the shear stress τ xy at the point.

A:

Q: A flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates…

A:

Q: Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw…

A: