Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal andvertical planes at the point are Sx= 39 MPa, S, = 56 MPa, and Sy = 41 MPa.(a) Draw Mohr's circle for this state of stress.(b) Determine the principal stresses (op1 > op2) and the maximum in-plane shear stress Tmax acting at the point.(c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Thenshow these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)SySxAnswers:Opl =iMPa.On2 =iMPа.Tmax =iMPa.Opi

The stepwise procedure to solve this problem is shown in the following attached image:

Answered: Consider a point in a structural member…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx= 14 MPa, S, = 29 MPa, and Sy = 39 MPa. (a) Determine the principal stresses (o,1 > op2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Sy Answers: Opl = i MPa. Op2 = i MPa. Tmax = i MPa. Op i
The state of plane stress at a point is represented by the element shown in the figure. Oy o, = 200 Mpa oy = 450 Mpa Txy Try 3D200 Мра Click here to see all formulas Ox Part A - Determine the maximum principal stress in Mpa. O 253 О 355 O 507 O 760 O 608 Submit Request Answer O O O O O
The forces applied to the pulleys are given in the figure below. Accordingly, show the stress condition at point A on a 2-dimensional stress element and find the Von-Misses equivalent stress.
A roadway sign weighs 5.3 kN and is supported by a structural pipe that has an outside diameter of 220 mm and a wall thickness of 14.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.1 m, b=4m, P₂ = 13 kN, and Py = 5.3 kN. (a) Determine the normal and shear stresses. Txy at point H. (b) Determine the normal and shear stresses Ok Tysk at point K. Answers: 0|| = Tryll = 0k = Tyck= i i MPa. MPa. MPa. MPa.
just part c, please
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan = 21.8°, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and z (magnitude only) at this point on the inclined plane shown. Answers: i MPa, T = i MPа.
The diagram below shows Mohr’s circle for a point in a physicalobject that is subjected to plane stress.(a) Determine the stresses σ x, σ y, and τ xy, and show them on astress element.(b) Determine the principal stresses and the maximum in-planeshear stress acting at the point, and show these stresses on anappropriate sketch
Find the interal normal stress in all relevant segments of the bar in the picture.
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
Calcuate Torsion From Point A to Point C and Bending from Point A to Point B and from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, 2750 psi, S, = 1100 psi, and Sy 1950 psi. Assume ß - 53°. (a) Draw Mohr's circle for this state of stress. %3D (b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16). (c) Determine the normal and shear stresses on the indicated plane and show these stresses on a sketch. (d) Determine the absolute maximum shear stress at the point. Sxy Answer: (a) Draw Mohr's Circle for this state of stress. (b) op1- psi Op2 - psi Tmax in-plane psi (c) on psi Tnt psi (d) Tabs max psi eTextbook and Media
At a point in a stressed body, the known stresses are o, = 42MPA (T), o, = 16 MPa (C), o, = 22 MPa (T), ETry = 40 MPa, Tyz 0, and Tex = 27 MPa. Determine (a) the normal and shear stresses on a plane whose outward normal is oriented at angles of 38° 77°, and 55.03° with the x, y, and z axes respectively. (b) the principal stresses and the absolute maximum shear stress at the point. Answers: (a) on = i MPa Tnt = MPa (b) Opl = i MPa Op2 = i MPa Op3 = i MPа Tabs max = i MPa

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS