A roadway sign weighs 5 kN and is supported by a structural pipe that has an outside diameter of 295 mm and a wall thickness of 10 mm. The resultant force of the wind pressure acting on the sign is 12 kN, as shown. Assume a = 9 m, b = 5.2 m, P₂ = 12 kN, and Py = 5 kN. (a) Determine the normal and shear stresses OH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH = TxyH = OK = y HK i i i P₂ Tyzk= i b a MPa. MPa. MPa. MPa.

A roadway sign weighs 5 kN and is supported by a structural pipe that has an outside diameter of 295 mm and a wall thickness of 10 mm. The resultant force of the wind pressure acting on the sign is 12 kN, as shown. Assume a = 9 m, b = 5.2 m, P₂ = 12 kN, and Py = 5 kN. (a) Determine the normal and shear stresses OH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH = TxyH = OK = y HK i i i P₂ Tyzk= i b a MPa. MPa. MPa. MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A roadway sign weighs 5.3 kN and is supported by a structural pipe that has an outside diameter of 220 mm and a wall thickness of 14.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.1 m, b=4m, P₂ = 13 kN, and Py = 5.3 kN. (a) Determine the normal and shear stresses. Txy at point H. (b) Determine the normal and shear stresses Ok Tysk at point K. Answers: 0|| = Tryll = 0k = Tyck= i i MPa. MPa. MPa. MPa.
Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress-30 MPa
In the figure, both ends of the rectangular plate are under the effect of a force p = 150kN. What is the value of the shear stress occurring in the NN 'plane which makes an angle Q = 30 ° as shown in the figure? cross-sectional area is 100mm ^ 2.
The stepped shaft shown in the figure is supported by bearings at A and B. Determine the maximum stress in the shaft due to the applied couples. The shoulder fillet at the junction of each shaft has a radius of r = 6 mm.
For the stress state shown in the figure below, use the Mohr’s circle method to determine (a) the maximum and minimum principal stresses, (b) the orientations of the maximum and minimum principal stresses (c) how the principal stresses on a properly oriented element. (d) Draw Mohr’s circle using a ruler and a compass
A rail line is laid so that there is no stress in rails at 15°C. The rails are 500000 mm long. α = 11.7 × 10-6/°C and E = 2.3 × 105 N/mm2. Find the maximum temp. to have no stress in the rails if the expansion allowance is 15 mm/rail.
Given the beam and the external loading shown below, if L = 15 m, w1 = 510 N/m and w2 = 1,600 N/m, calculate: • the magnitude and location of the equivalent resultant force (a single equivalent force, for the whole loading block, NOT two equivalent forces from dividing into rectangular and triangular stress blocks). • the reactions at the beam supports. W2 w, A L Resultant force Fr = 单位 (tolerance 1 N, magnitude only) Location xbar = 单位 (tolerance 0.1 m, measured from A) Reactions: Ay = 数字单位 (tolerance 1 N, observe up positive sign convention) MA= 数字单位 (tolerance 10 N*m, observe anti-clockwise positive sign convention)
Z 300, mm- 500 mm- $ 30 mm X 600 N The normal and shear stresses in MPa at point P are respectively (a) 67.9 and 56.6 (b) 56.6 and 67.9 (c) 67.9 and zero (d) zero and 56.6
A flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates is shown in the figure. The plates are 160mm long and 80mm wide. (a) Determine the force that can be applied to the arrangement, if it is not to exceed a shear stress of 350kPa
Figure Part A Fuc= 0.97 5m HA 2m KN Determine the magnitude of the projected component of the F-5 kN force acting along the axis BC of the pipe. Suppose that a 3.1 m and b=4.4 m (Figure 1) Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining B ? a 1m 1 of 1
Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw the graph of the neutral axis and normal stress next to the section. Find the normal stresses in kg / cm2. P =16964 KG EX=20 cm EY=6 cm
How do I calculate for sigma seam? Thank you