The ice weighs 5 kg and is 30 cm wide across the tongs. The distance between the handles is 12 cm and the mean radius r of a tong is 18 cm. The rectangular cross-section dimensions are 3 cm deep and 1 cm wide (in the out of plane direction) . Find the forces and bending moment in the tongs at the section indicated by point A. Also determine the stresses acting on the inner and outer surfaces at this section.

The ice weighs 5 kg and is 30 cm wide across the tongs. The distance between the handles is 12 cm and the mean radius r of a tong is 18 cm. The rectangular cross-section dimensions are 3 cm deep and 1 cm wide (in the out of plane direction) . Find the forces and bending moment in the tongs at the section indicated by point A. Also determine the stresses acting on the inner and outer surfaces at this section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. The modulus of elasticity is Est = 200 GPa for steel, and E. = 24 GPa for concrete.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A circular plate with simply supported edges subjected to a uniform pressure of P=10 KPa, as shown below, is considered. The plate thickness is h=19 mm, and the plate radius is RO=1,340 mm. If Young's modules and Poisson's ratio are assumed to be E=70 GPa and V=0.5, respectively, workout the slope of the plate at the centre. (NOTE: round-off your answer to 4 decimal places, and write your answer without considering any negative (-) sign). Ro Your Answer:
3. Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8. Find the maximum shear stress in each shaft. Diameter A C = 30 cm Diameter CB = 20cm 0.5cm 1 cm
Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw the graph of the neutral axis and normal stress next to the section. Find the normal stresses in kg / cm2. Load(P)=44473kg ex=10cm ey=8cm
A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is wound closely with a single layer of circular wire of diameter 1.2 mm. Under the tension of 96 N/mm'. If the cylinder is treated as thin. Calculate (1) Initial stress in cylinder. (ii) Initizl pressure which will produce a stress of 48 N/mm2.
The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA, a = 15×106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle e through which the beam AC would rotate due to this temperature change. -200 mm -80 mm A B -"Rigid" |(1) (2) 250 mm
A steel beam of length 5 m is heated to a temperature difference of 50 degrees. calculate (a) stress developed in the beam when both ends are fixed and (b) change in length when one end is free to expand (a, =11.7x10 /°C, E = 210 MPa). (A) (a)o=112.85 MPa (b) 8 = 0.002925 m (В) (а)o — 225.7 MPа (b) 8-0.02925 m (C) (a)o =112.85 MPa (b) 8 = 2.925 m (D) (a)o =112.85 MPa (b) d = 0.002925 mm ||
For the system below , find the maximum stress for the member ECD due to the combined effect of axial and bending moment .
A polyethylene bar having rectangular cross section with a width 7.35 in. and depth 7 in. is placed insidea hollow steel square section with side dimension of8 in. The polyethylene bar is then compressed by an axialforce P. At what value of the force P will the gap betweenthe polyethylene bar and the steel tube be closed for thefirst time on one side? What is the remaining gap betweenthe polyethylene bar and the steel tube on the other side?For polyethylene, assume E 5 200 ksi and n 5 0.4.1
Q4/ cylinder has an internal diameter of 200 mm, has walls 3 mm thick and is 1.2 m long. It is found to change in internal volume by 11x10 m' when filled with a liquid at a pressure p. If E=200 GN/m? of hoop and v-0.25 determine the values and longitudinal stresses?
A torque of T=2kNm and a torque of M=1kNm are applied to the thin-walled pressure tank as shown in the figure. Calculate the maximum internal pressure (p) that can be applied to the tank according to the von Mises distortion energy theory, with the radius of the tank r=50mm, the wall thickness t=3mm and the safety factor n=2.3. The yield strength of the tank material is Sut=380MPa.