Direct stresses of 160N/mm2 tensile and 120 N/mm2 compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm2. What must be the magnitude of the shearing stresses on the two planes? What will be the maximum shearing stress at the point?

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: 4 The state of stress on an element at a point is described by the Figure shown. Stress magnitudes:…

A: The objective of the question.(a) Neatly sketch the Mohr's Circle, identifying the locations of the…

Q: he stress condition given in the figure, find the approximation o

A:

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A: A perpendicular force applied on a body per unit area is referred to as a stress. There are three…

Q: occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane.…

A:

Q: The Center point co-ordinates of the Mohr's circle is: (Use comma between x and y co-ordinates, Do…

A:

Q: Determine approximately the principal stresses of a point whose stress states are shown below.…

A: In the above stress diagrams,  are not given with values so considered 0.

Q: given figure, 40 kN 60 KN determine the .D normal stress + 2m - Sm Sm in MPa at segment AB.…

A:

Q: (a) the principal stresses and the positions of the plane on which they act (b) the position of the…

A: here all angle measure from vertical plane and in counter clock wise direction, if in calculation…

Q: Problem 1: Given the 2D states of plane stress below, determine the principal stresses (0₁, 0₂) and…

A:

Q: The rectangular components of the stress at a point in a machine are given by 2 3.6 2.4 3.6 2.4 4…

A: Given- stress matrix shown belowTo Find-Find the normal, shear, and resultant stresses on a plane…

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: The following stress condition is applied on a material: 400 200 0 o 200-300 0 MPa 000 Determine the…

A:

Q: Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here,…

A:

Q: Q1: A certain point in the mechanical part shown in Figure below. Use Mol determine: (a) the…

A: Givenσx=60 MN/m2=60MPaσy=-50MN/m2=-50MPaτxy=30MN/m2=30MPa

Q: At a point in a strained material, if two mutually perpendicular tensile stresses of 200 kg/cm² and…

A:

Q: In an elastic material under load, two planes, AB and BC, are perpendicular to each other. The…

A: to find (a) principle stresses and direction of the principle stresses(b) normal and shear stress on…

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: 4. What are the maximum and minimum stresses for a circular hole in a plate subjected to pure shear?…

A: Step 1: Step 2:

Q: The state of stress at a point in a member is shown in Figure Q1(a). Determine the stress components…

A:

Q: 2.4. The stress at a point is defined by the components Og =0 MPa, Oyy =100 MPa, Oxy = Oyx = -40…

A: Given Data⇒σxx=0 MPaσyy=100 Mpaσxy=σyx=-40 MPaProblem definition⇒Problem says find principle…

Q: Q3) Consider the figure and dimensions of Problem 1.37. Given that Q=600 lb, determine; a) The…

A:

Q: In a simulation carried out by a team engineers a state of plane stress in a machine base of a…

A: To find - 1. The principal stresses and the maximum in- plane shear stress acting at the point.…

Q: Determine the maximum shear stress acting at section a-a of the cantilevered structure, as shown in…

A:

Q: cm=10 MPa 1. Normal and shear stress at points A a their types (i.e. normal stress is t compression…

A:

Q: In a volume element with dimensions dx, dy, dz the negative y-face has a 2 MPa stress in the…

A:

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

A:

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are o, 400…

A: The stress on the x plane is σx=400 MPa The stress on the y plane is σy=-300 MPa The shear stress on…

Q: A body is subjected to multiple applied loads. The resultant stress at point location (0, 1, 4)…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: The state of plane stress at a point is represented by the stress element below. Determine the…

A:

Q: Can you help me with this problem, please:   At a material point in plane stress it is known that…

A: Magnitude of principal stresses:The principal stresses can be determined using the stress…

Q: 4. The values of the normal (ON) and shear stresses (TN) in the plane making an angle of 60° with…

A: Stress When body is subjected to a force then body will resist that force and the resistance is…

Q: 1.5 kN 120 mm Outer diameter: 72 mm Inner diameter: 62 mm 150 mm 120 mm 4.5 kN A For element A find:…

A: Evaluate the equivalent couple about longitudinal axis of hollow circular shaft (that is axis…

Q: A strain element is given in the figure. Find the planes in which the normal stresses are equal in…

A:

Q: The stresses shown below act on horizontal and vertical planes through a point on the surface of a…

A: The stresses shown below act on horizontal and vertical planes through a point on the surface of a…

Q: Q5: At a point in a strained material the stresses acting on planes at right angles to each other…

A: