Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500 mm, b = 250 mm, h = 330 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a i 1.418 B 8 KN h

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500 mm, b = 250 mm, h = 330 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a i 1.418 B 8 KN h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: he davit shown in the figure is supported by a cable at B and pinned at A and is subjected to a…

A: To Find : The normal stress in the tie rod (1) The shearing stress in the pin at A The shearing…

Q: A rigid plate (AC) is connected to flat steel bars by pins at A and B. The horizontal flat steel bar…

A: A rigid plate (AC) is connected to flat steel bars by pins at A and B. The horizontal flat steel bar…

Q: 4.00kips Ib 600 ft Problem 3. Pin B acts in double shear and has diameter d=3/4 in. Pins are…

A: Given data: The diameter of the pin, dB=34 in. The failure stress is, τfailure=12000 psi. Draw the…

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

Q: The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA, a = 15x106/°C)…

A: (a) Moment acting about point B is PA0.2=Pc0.08PA=0.4Pc⋯⋯⋯(1) According to the compatibility…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: H.W.2 A 60 mm wide by 8 mm thick steel plate is connected column o a gusset plate by a 20 mm…

A: 1)-Normal stress on surface area:Agross=60mm×8mmAgross=480mm2

Q: 2. Two elastic bars are connected and supported as shown. The thermal load is a 10°C temperature…

Q: 4) A 50 mm diameter solid steel shaft supports loads P₁= 1.5 KN and P = 3.0 KN, as shown. Assume L₁…

A: (a) To find: The maximum shear stress. Given: The diameter of the shaft is d=50 mm1 m1000 mm=0.05 m.…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double-
shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500
mm, b = 250 mm, h = 330 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot
exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure.
D
Answer: Pmax
(1)
a
i
●
1.418
B
●
●
b
kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 45-mm-diameter solid steel shaft supports loads PA = 1.1 kN and Pc = 2.2 kN as shown. Assume that L₁ = 155 mm, L₂ = 330 mm, and L3 = 240 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. A L₁ Answers: (a) Tmax= (b) max = i B L2 Pc MPa MPa L3 D
number 5.5
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a = 250mm, b = 170mm, c = 80mm, and 0 = 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket A Answers: Tpin B = i Ob= i Bell crank a B b MPa MPa
An angled strut b = 6.2 in. thick is subjected to a force F = 55 kip and a uniformly distributed load q = 23.5 kip/ft as shown below. Determine the principal stresses at points A, B, and C. (op1) A = (0₂2) A = (pl) B = (p2)B= (pl) c = (p2) c = = 15 in. 10 in. number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) F 12.5 in. -7.5 in.- -12.5 in. ksi ksi ksi ksi ksi ksi q
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 550 mm, b = 275 mm, h = 450 mm, and 8= 50°. If the normal stress in tie rod (1) cannot exceed 180 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a B P
A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below. Determine and draw the state of stresses in small infinitesimal cubic elements located at points M and N on the cross section A.
3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the maximum shear stress in each segment and the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. a. Tab= b. Tbc= C. Tbc= ad= 1100 N·m 800 N·m D C 900 N·m 600 N m B A 2 m3 m2 m
A compound shaft consists of an aluminum tube (1) securely jointed to a steel tube (2). Both aluminum and steel tubes have an outside diameter of D= 48 mm and a wall thickness of t= 3 mm. The shaft is secured by a fixed support at one end and is subjected to a torque of T= 115 N.m at the other end. Determine the maximum stress in the shaft.[L1 = 200 mm, L2 = 350 mm, D = 48 mm , t = 3 mm, G = 75 GPa]
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress at the pin C is 40 MPa.
Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN