H.W.2 A 60 mm wide by 8 mm thick steel plate is connectedto a gusset plate by a 20 mm diameter pin. If a load of P =70 kN is applied, determine the normal, shear, and bearingstresses in this connection.columnpin diameter = 20 mmgussetplatesteelplate70 kNpin60 mm8 mm platethickness

1)-Normal stress on surface area:Agross=60mm×8mmAgross=480mm2

H.W.2 A 60 mm wide by 8 mm thick steel plate is connected column o a gusset plate by a 20 mm diameter pin. If a load of P = 70 kN is applied, determine the normal, shear, and bearing pin diameter = 20 mm gusset plate stresses in this connection. steel plate 70 kN pin 60 mm 8 mm plate thickness

H.W.2 A 60 mm wide by 8 mm thick steel plate is connected column o a gusset plate by a 20 mm diameter pin. If a load of P = 70 kN is applied, determine the normal, shear, and bearing pin diameter = 20 mm gusset plate stresses in this connection. steel plate 70 kN pin 60 mm 8 mm plate thickness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7…

A: Diameter of tie rod (1) = 7 mmDiameter of pin B = 5 mmLengths:a = 670 mmb = 335 mmh = 370 mmAngle=to…

Q: Q7-Q8: A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of…

A: Longitudinal Stress, σlong = σx = 15 ksi. Tangential Stress, σtang = σy = 45 ksi.

Q: H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C (…

A: 1. Draw a diagram for the given cross-section. Here, A, B, C, D, E, F indicate the shown rivets, Fp…

Q: - 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm…

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 16 mm,…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: 3. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A: Given Data The load applied at D is: P=20 kips The coefficient of thermal expansion is:…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: 4.00kips Ib 600 ft Problem 3. Pin B acts in double shear and has diameter d=3/4 in. Pins are…

A: Given data: The diameter of the pin, dB=34 in. The failure stress is, τfailure=12000 psi. Draw the…

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

Q: mm. When subject to pressure, the hoop stress in

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: An object weighing 40 N is drop from a height of 4 m and hits a vertical steel rod on top. Determine…

A: Weight of object = W = 40 NHeight of drop = h = 4 m = 4000 mmDiameter of rod = d = 4 mmLength of rod…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: Problem 4.28 The observation cage C has a weight of 250 kip and through a system of gears, travels…

Q: An engineering machine component operating in a high temperature environment consists of a copper…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Diameter of Tie rod (1) d1=11 mm Allowable normal stress =165 MPa. Outside diameter of Pipe (2)…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum…

Q: Determine the bolt stress for an internal pressure of 500 psi.

A: Given dataequally spaced steel bolt the diameter of the bolt the pre-load of each bolt the number…

Q: Q3/ Two plates are riveted together have a width of 130 mm, thickness of 25 mm and the diameter of…

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Question

H.W.2 A 60 mm wide by 8 mm thick steel plate is connected
to a gusset plate by a 20 mm diameter pin. If a load of P =
70 kN is applied, determine the normal, shear, and bearing
stresses in this connection.
column
pin diameter = 20 mm
gusset
plate
steel
plate
70 kN
pin
60 mm
8 mm plate
thickness

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve this one urgently
Include the FBD of the Problem
مقاومه HW2
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
The bell-crank mechanism is in equilibrium for an applied load of P = 47 kN. Assume that a = 300 mm, b = 225 mm, and 0 = 57°. The pin at B has a diameter of d = 14 mm, and the bell crank has a thickness of t = 8 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: Bell crank A O= i 34.21 a с MPa B Support bracket b F₁ IF B
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 570 mm, b = 285 mm, h = 360 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h B a Answer: Pmax i b kN
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
number 9
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1320 mm². Assume a = 2.4 m, b = 9.7 m, and c = 3.6 m. If P = 60 kN and Q = 70 kN, determine the normal stress in each member. a Answers: OAB = i MPa (C) MPa (Т) i MPa (Т)
The subject is Mechanics of Deformable Bodies
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1060 mm?. Assume a = 1.6 m, b = 9.8 m, andc = 3.6 m. If P = 60 kN and Q = 85 kN, determine the normal stress in each member. P В Q< b. Answers: OAB = i MPa (С) OBC = i MPа (Т) OAC i MPа (Т)
PLEASE ANSWER QUICKLY