The tip of a cutting tool has stresses at the surfaces, as shown in the sketch. On theupper surface, o is a normal stress and t is a shearing stress. Also, it is known thatTxy = - 15.9 MPa. Determine ox and oy. Then, determine the shearing stress t onthe upper surface.y20°20°30°90°13.53 MPa35.39 MPa(Final Answer: Ox = - 22.7 MPa, oy = 33.8 MPa, t = 30.3 MPa)

Given data, τxy = -15.9 MPa To determine:- σx and σy Shear stress of the upper surface

Answered: The tip of a cutting tool has stresses…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated in the figure.
Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure.
At a point in a strained material the principal stresses are 200 N/mm2 (tensile) and 120 N/mm2 (compressive). Determine the normal stress, shear stress and resultant stress on a plane inclined at 30° to the axis of major principal stress. Also determine the maximum shear stress at the point.
None
The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at point B.
Two solid steel wall supported shafts are connected using the 4 bolt flange. A torque is applied to one side of the bolted connection. Using G = 11.2x10 psi determine the shear stress in the 4" diameter bolts which are on a 2.5" bolt circle diameter. Solve with the applied torque on the left side coupling as shown. Also determine the bolt shear stress if the applied torque was on the other side of the coupling. 1.5 in. 1.25 in. T-350 lb ft 3 ft 2 ft
The 20 mm diameter rod is subjected to the loads shown.(a) Determine the state of stress at point and show the results on a differential element located at this point.(b) Using Mohr's circle, determine the maximum normal stress and the maximum in-plane shearing stress at point A and show the associated stress states on appropriately oriented elements, for cach case.
Q!n find the change in temperature in the Steel Yod only so that Point B moves 2mm to the right? Determine the thermal Stresses in each rod ? Steel aluminume 2m 3.Sm
For a steel rod with a circular cross section with a diameter of D = 20 mm, the following is required: 1. Draw a diagram of the longitudinal force 2. Draw a diagram of normal stresses 3. Determine the total elongation of the rod if Е = 2∙10^5 MPa When calculating, take: а = 2 m, b =1.2 m, F=10 кN - The point of application of force! The work must be done on one sheet of A4 paper, which must show: - Using the method of sections to determine the longitudinal forces in the rod. - Draw a diagram of longitudinal forces N - Determination of normal stresses based on the constructed plot of longitudinal forces. - Draw diagram a normal stresses - Determination of the full extension of the rod
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The tip of a cutting tool has stresses at the surfaces, as shown in the sketch. On the upper surface, o is a normal stress and t is a shearing stress. Also, it is known that Txy = - 15.9 MPa. Determine Ox and oy. Then, determine the shearing stress t on the upper surface.