The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear). Determine the diameter of the smallest pin that can be used without exceeding the allowable shearing stress in the rivet is 70 MPa. Express your answer in "mm" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required * 10m

The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear). Determine the diameter of the smallest pin that can be used without exceeding the allowable shearing stress in the rivet is 70 MPa. Express your answer in "mm" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required * 10m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flange bolt coupling is used to connect two solid shaft 125 mm in diameter. If the shearing stress is 85 MPa, how many 12 mm bolts must be used on a 250 mm diameter bolt circle to carry the load? (Round up to whole number)
For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine the shear stress in the 1 inch diameter pin at A which is in double shear: Calculate your answer to 1 decimal place. 7' 5' B W lb/in².
Ten bolts of 10 mm diameter are used to connect two shafts as shown. If the mean diameter of the circle is d = 200 mm, and the failure shear stress of the bolt’s material is 70 MPa, determine the maximum permissible torque (N.m). Take F.S. = 1.05. (Input the answer with two decimal places; like 263.46, 3682.42, ....).
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress s limited to 5000 psi. Assume single shear. 4R + 3t
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.55 in and the weight of the bar is 5391 lb. Round off the final answer to 3 decimal places.
NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5205 lb. Round off the final answer to two decimal places.
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine the shear stress in the 1 inch diameter pin at A which is in double shear: ____ lb/in2. Calculate your answer to 1 decimal place.