A flanged bolt coupling is used to connect a solid shaft 85 mm in diameter to a hollow shaft 100 mm in outside and 85 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 66 MPa, how many 10-mm-diameter steel bolts must be used on a 185-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft? Round off the final answer to two decimal places.

A flanged bolt coupling is used to connect a solid shaft 85 mm in diameter to a hollow shaft 100 mm in outside and 85 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 66 MPa, how many 10-mm-diameter steel bolts must be used on a 185-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft? Round off the final answer to two decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the max shear stress on a shaft under a torque of T = 54.167 lb-ft having a diameter of 0.75 inches? (answer in psi). Note: Final Answer in 4 decimal Places.
A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
Question 1 Pulleys A and B with the dimension of 66 mm in diameter are connected to solid shafts AB and BC, respectively as shown in Figure 1. The red arrow printed on pulleys A and B are the direction of rotation of the torque. If the force applied to pulley A is 5 kN and to pulley B is 5 kN, Compute: 30 mm В a) The maximum shearing stress in the shafts АB and BC. 46 mm b) The angle of twist for at end A with the modulus of rigidity 26 GPa. Figure 1
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 263 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 9494 Nm without exceeding a shearing stress of 46.89 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
The topic is all about the different kinds of stresses the simple stress, simple normal stress, simple shearing stress. Also, show the conversion in the solution. Please use and paper to solve and use 3 decimal places. Provide also a step-by-step solution to be able to understand Thank you.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.8 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 88.86 MPa and its angle of twist is limited to 5.15˚. Use G = 80.77 GPa for steel and L = 462 mm. Round off the final answer to two decimal places.
Determine max for a 40-mm diameter shaft if the allowable shearing stress is equivalent to 80 megaPascal 0.529 kN-m 0.435 kN-m 0.421 kN-m 4.35 kN-m None of the choices are correct.
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 262 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 200 mm in diameter. If the torque that can be applied is 7381 Nm without exceeding a shearing stress of 44.07 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
Four bolts used to lap joint two steel plates together. Tensile force on the plates is 66.7 kN. Determine the diameter of the bolt if the allowable shearing stress is 68.9 MPa. A. 15.4 mm C. 18.4 mm B. 17.6 mm D. 19.6 mm
Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the other four pins has a 16mm diameter. a. Determine the maximum value of the average normal stress in the links connecting points B and D and points C and E. b. Determine the average shearing stress in points B and C.
QUESTION 3 Determine the maximum shearing stress (MPa) in a solid shaft of 61-mm diameter as it transmits 92 kW at a speed of 144 rpm.
A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter steel bolts on a circle of diameter 400mm and six 10mm diameter steel bolts on a circle of diameter 300mm. Determine the shearing stress in the bolts at the outer bolt circle (2 decimal places in MPa).