The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.66-in .-diameter pin at A, and the 0.28-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5066 lb. Round off the final answer to two decimal places.

The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.66-in .-diameter pin at A, and the 0.28-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5066 lb. Round off the final answer to two decimal places.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

*NOTE ON INSTRTUCTUONS AND HINTS
Figure a 1.5 in. 1 in. 0.5 in. 0.5 in. 3 in. - 3 in.
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Page 6 of a Another name for "SIZE DESCRIPTION" is: A Dimensioning. B Orthographic projection. C Assembly drawing. D Pictorial drawing What is the length to width ratio of arrowheads? A 1:1 37 42 в 2:1 С 3:1 D 5:1 Leader lines should NOT be drawn: 38 "2X on a hole note means: 43 A At 45°. A Double the size of the hole. B At 30°. C At 60°. D Horizontally or Vertically. B Reduce the stated size by 1/2. C The scale of the hole is doubled. D There are two boles the same size. Extension lines are drawn: 39 Avoid dimensioning to: 44 A Extremely thick, A Hidden lines. B Thick. B Center lines, C Thin. D Extremely light. C Extension lines. D Holes. What is the standard length for arrowheads? CIRCLE SIZE is specified by: 45 40 A 031 (.5mm) B 063 (Imm) A Chord. B Circumference. C Diameter. C. 125 (3mm) D 250 (6mm) D Radius. Dimension lines should be: 41 46 The size of an ARC is typically specified by its: A Thick and dark. A Diameter, B Thick and light. B Circumference. C Chord. C Thin and dark.…
Convert 22C to Fahrenheit.
a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm3 ); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm2 and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m2 per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine.
Solidworks
Solidworks
Please only answer number 8
Do not use Ai to answer this question.
Please Carefully solve. Don't make mistake. Thank you.
300 mm 300 mm Figure Q2