Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.89 in2 P = 1716 lb, x = 16.3 in, y = 11.8 in, and z = 10.9 in. Round off the final answer to three decimal places.

Q: Consider a hollow circular shaft of inner radius r; = 1.25 inch and outer radius of ro = 1.50in,…

A: Find the state of stress at point P

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given data: FS=2.2σfail=614  MPa Need to determine the allowable stress for member σallow.

Q: Bar AC supports two loads, X = 355 N and Y= 355 N as shown. Rollers at A and Crest against…

A:

Q: A faucet is shown on the figure below. A force of P = 1100 lb is exerted at both ends of the faucet…

A: Given:To find:Least possible diameter

Q: Maximum shear stress theorem, determine the factor of safety at point H,

A: Given: Yield stress=200 MPa  To determine:  FOS according to maximum shear stress theory

Q: At a temperature of 22.8 °C a 0.44-mm gap exists between the ends of the rods shown. At a later time…

A:

Q: 3. Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at…

A: Given Data Dimensions of the beam are 4in×3in Area, A=4(3)=12 in2 Moment of inertia, I=3(4)312=16…

Q: an acetylene tank consists of a cylindrical body flat at its base and hemisphere at the other end .…

A: Thickness, t=2 mmDiameter, d=250 mmL=1200 mmσper=180 MPaHoop stress/Circumferential stress,…

Q: Period: This bridge spans a 10ft wide creek. A 30lb downward force is located at the top center of…

A: To Find :  The x and y components, what is the load and the T or C for each member. Given:  The load…

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Show the force and moments on cross section H.

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: 13.Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A:

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable…

A:

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN,…

A: Given: P = 8 kN the normal stress and shear stress are calculated for mentioned plane using formula.

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Consider the cross-section of the beam, Calculate the centroid of the section,…

Q: - 24 in.- D 10 in. B| C y

A:

Q: I 10'- 50° F E -10'- -10'- G 8' H D A 2 kips 20° 4 kips 4 kips 2 kips

A:

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 18.86 ksi for…

A:

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: P= 189.3 kN= 189.3(1000) N= 189300 N Cross sectional area of the bronze, ABronze= 400 mm^2 Magnitude…

Q: Determine the magnitude of the force (lb) in member BD of the truss shown if P = 32693 lb, Q = 35423…

A:

Q: The axial load 296 kN applied to the lap joint is distributed equally among the three…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: Determine the  magnitude of  force (kN) in member AB if F=76532 N , a=2.93m , b=1.42m and c=4.16m.…

A: Draw a diagram for the problem. Here, θ and α are angles as shown in the diagram.

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a bras tube which…

A: Given Data The diameter of steel bar is:dsteel=28 mm=0.028m The length of steel bar is:L=0.4 m The…

Q: Draw Mohr’s circle that describes each of the following states of stress.

A: The maximum and minimum stresses are known as the principal stresses. The angle of the plane is two…

Q: A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a…

A:

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal…

A:

Q: Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 147 MPa and 190…

A:

Q: Determine the  magnitude of  force (kN) in member AB if F=67139 N , a=3.46m , b=0.91m and c=5.51m.…

A:

Q: Given; A = 500 mm2, Load 1 = 25 kN, Load 2 = 50 kN. Solve the stress in Part BC. (Write answer in 2…

A:

Q: 5. A cylinder having a mass of 250 kg is to be supported by the cord which wraps over the pipe.…

A:

Q: Determine the  magnitude of  force (kN) in member BC if F=66188 N , a=2.75m , b=1.15m and c=4.11m.…

A:

Q: Determine the force in each member of the space truss given F-3 kN. Use positive to indicate tension…

A: Ans Given Now the coordinates of various point areNow calculate the unit vector along AD asAgain…

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final…

A:

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

A:

Q: tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter…

A:

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: A 76-kN centric load must be supported by an aluminum column as shown. Using the aluminum alloy…

A: To Find : The minimum dimension b that can be used Given : The comcetric lad is

Q: 11. A pressure vessel containing gas at 250 psi has an outer diameter of 18 inches and a thickness…

A: Hoop stress in the cylinders will increase the diameter of cylinder.  Longitudinal stress will cause…

Q: Using the method of joints, determine the magnitude of force (Ib) in member AC of the truss shown if…

A:

Q: solve, show all steps/solutions. include all asked for, no partial answer or ill dislike

A: Given that,The diameter of rod = d = 1 inchHence, radius of rod = r = 0.5 inchConsider following…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.