The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.32-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5351 lb. Round off the final answer to two decimal places.

Q: A faucet is shown on the figure below. A force of P = 1100 lb is exerted at both ends of the faucet…

A: Given:To find:Least possible diameter

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A:

Q: 70 4 in 3.5 in. | 30° 0.5-in dia. Detail at A 12 ft

A: given; load(P)=28.96KNAC=12ft     =3.65mdiameter(d)=20.75mmlets take horizontal reaction force at…

Q: Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A…

A:

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable…

A:

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Q: The lap joint is fastened with four 0.87-in.-diameter rivets. The working stress is 12.34 ksi for…

A:

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Consider the cross-section of the beam, Calculate the centroid of the section,…

Q: - 24 in.- D 10 in. B| C y

A:

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 18.86 ksi for…

A:

Q: Determine the shear stress (in Mpa) in the 28.36-mm-diameter pin at A that support the beam if P =…

A: P= 29.48 kN= 29480 N a= 2.86 m b= 5.57 m At A, the pin diameter, D= 28.36 mm   To find: Shear stress…

Q: Q3/ If two members, A and B, are connected together and fixed supported at one end. The tensile load…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is…

A:

Q: Three identical plates of 62 mm wide and 7 mm thick connected by a square pin with side dimension 12…

A:

Q: A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a…

A:

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

A:

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16…

A:

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension…

A:

Q: The frame for a sign is fabricated from a thin, flat steel bar stock of mass per unit length 4.73…

A:

Q: 2.) Solve for the normal stress of rod AB with a diameter of 10mm if the block has a mass of 40kgC…

A:

Q: In this figure is a strut and a cable which was use to lift a body. If the strut and a cable has a…

A:

Q: Determine the principal stresses and the maximum shearing stress at point H. (Round the final…

A: At point H, loading will be as per following, M=600(2.5)=1500 lb-inT=600(2.5)=1500 lb-inP=2300 lb…

Q: Determine the shear stress (in Mpa) in the 35.29-mm-diameter pin at B that support the beam if P =…

A:

Q: Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod= 2300…

A:

Q: Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100

A:

Q: 1200 N 800 N 400 N D 2 m B A K J 2 m E 2 m 2 m G 2 m H Using Method of Sections (one cutting section…

A:

Q: Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of…

A: Given: Number of turns (n)=19turnsDiameter of the wire (d)=0.96inMean radius (r)=3.53inLoad…

Q: Situation 1 Determine Elő at point B and end of the overhang. Round off your final answer in 2…

A:

Q: For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to…

A: Bolt diameter, d=0.287 inShear stress, τ=29 ksi

Q: For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.