70 4 in 3.5 in. | 30° 0.5-in dia. Detail at A 12 ft

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given data: FS=2.2σfail=614  MPa Need to determine the allowable stress for member σallow.

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: Seven 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the maximum and minimum…

A:

Q: Given data Tensile force=D30 KN Rectangular section width=5 m Depth =10 m Determine stress

A: Given data, Tensile force= F = 30 KN = 30000 N Rectangular section width=b =5 m Depth =h =10 m…

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

A:

Q: For the selected design, determine the actual value of om in the beam. (Round the final answer to…

A: Given:Allowable Normal Stress For The Steel Used Is 25.2Load = 48 kipsTo find:lActual value of…

Q: 3a) Determine the x component of reaction force at F (F) in Newtons.

A:

Q: The lap joint is fastened with four 0.87-in.-diameter rivets. The working stress is 12.34 ksi for…

A:

Q: A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load…

A:

Q: A solid aluminum shaft of 94 mm diameter fits concentrically in a hollow steel tube. Determine the…

A:

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Consider the cross-section of the beam, Calculate the centroid of the section,…

Q: The eyebolt shown in Figure below, the allowable shear stress for the supporting material is Tallow…

A: Given data Allowable shearing strength=48MPa

Q: - 24 in.- D 10 in. B| C y

A:

Q: Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.89 in2 P =…

A:

Q: value of ơm in the beam is |ksi.

A:

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 18.86 ksi for…

A:

Q: Determine the shear stress (in Mpa) in the 28.36-mm-diameter pin at A that support the beam if P =…

A: P= 29.48 kN= 29480 N a= 2.86 m b= 5.57 m At A, the pin diameter, D= 28.36 mm   To find: Shear stress…

Q: The axial load 296 kN applied to the lap joint is distributed equally among the three…

A:

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: 1000 Ib -12 ft 12 ft- B 2000 lb 8 ft D. ton -12 ft- 6 ft 6 ft

A:

Q: A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a…

A:

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal…

A:

Q: Q1: Find the maximum flexural stress in the shown beam. 30 kN 50 kN to 100 mm 1m 3 m 2 m 80 mm

A: A pin support will exert both horizontal and vertical components of the reaction. The support B is…

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

A:

Q: Required information Know that oạall = 151 MPa and Tall = 100 MPa. |275 kN B D 275 kN -3.6 m 1.5 m…

A:

Q: Problem 1-81: Determine the required diameter of the pins at A and B if the allowable shear stress…

A: τallow =100 MPa

Q: Given; A = 500 mm2, Load 1 = 25 kN, Load 2 = 50 kN. Solve the stress in Part BC. (Write answer in 2…

A:

Q: 5. A cylinder having a mass of 250 kg is to be supported by the cord which wraps over the pipe.…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16…

A:

Q: tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter…

A:

Q: Determine the maximum w that can be applied if the shear stress limit is 100 MPa. Then determine the…

A:

Q: Determine the magnitude of the force in member EF (Ib) of the Pratt bridge truss shown if h 10.6 ft…

A:

Q: Question 5 Calculate the maximum longitudinal direct stress, plot the stress distribution diagram…

A:

Q: Problem 3 (Pro 3.19 Textbook modified): Using method of section. Solve for member FH using only one…

A: according to the given details in the question.

Q: Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension…

A:

Q: a unity. If you know that diameter of bolts 10 mm and it's allowable shear stress is 26 kN/m

A: FREE BODY DIAGRAM-   ΣMA=012×26×4×83-RB×8=0RB=17.333KNΣFY=0RA+17.3333-12×26×4=0RA=34.6667KN So that…

Q: find the average shear stress on the section of the inclined member if we were to cut it…

A:

Q: Determine the shear stress (in Mpa) in the 35.29-mm-diameter pin at B that support the beam if P =…

A:

Q: Determine the length (in meters) of the shortest 2-mm diameter bronze wire, which can be twisted…

A: ,

Q: 1. Find the internal force of member EG, FH, and FG using method of sections. 0.866 m 3KN 5 @ 1m

A: