The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for the rivets in shear. Find the bearing stress (in psi) on the plates. Assume that the load is equally distributed among the rivets. Round off the final answer to four decimal places. 013.png ... P W in. 8. in.

The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for the rivets in shear. Find the bearing stress (in psi) on the plates. Assume that the load is equally distributed among the rivets. Round off the final answer to four decimal places. 013.png ... P W in. 8. in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the stress (in psi) in member AB if the cross-sectional area of the BD is 1.90 in2 P = 1726 lb, x = 16.13 in, y = 12.8 in, and z = 10.7 in. Round off the final answer to three decimal places.
B 1 boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi AB cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places 70° 30° 12 ft C Р 4 in. 3.5 in. Detail at A H 0.5-in. dia.
4. two decimal places
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 267 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 8166 Nm without exceeding a shearing stress of 43.32 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
A flanged bolt coupling is used to connect a solid shaft 89 mm in diameter to a hollow shaft 100 mm in outside and 89 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 66.2 MPa, how many 10-mm-diameter steel bolts must be used on a 191-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft? Round off the final answer to three decimal places.
Answer for D
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 56 MPa in the shafts and 22 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.1 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 88.06 MPa and its angle of twist is limited to 5.02˚. Use G = 80.89 GPa for steel and L = 449 mm. Round off the final answer to two decimal places.
round off only at final. four decimal places. with explain please.
The allowalbe tensile stress for a 62.5mm diameter bolt with a thread length of 5.5mm is 207 MPa. The allowable shear stress of the material is 103 MPa. Compute the allowable shearing load on the thread.A. 4.35 kNB. 6.35 kNC. 2.45 kND. 5.56 kN
The two pieces of wood, 2.59in. by 5.69 in., are glued together along the 60°joint. Determine the normal stress (in psi) in the glue if the shear stress in the glue is limited to 352 psi. Round off the final answer to three decimal places. 017 shear.png ... P A
Two horizontal 5.82-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.68-in. diameter is used at each connection, determine the bearing stress (in psi) at Bin member AB. Round off the final answer to two decimal places.