10 kip 5 kip 3 kip

Q: how do we know these values if they're not given

A: Below is the answer to your query.

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: The steel shafts is made from two segments AB and BC, which are connected together using a fillet…

A:

Q: The solid shaft is loaded (two point loads) and supported (fixed at left end) as shown. For the xyz…

A: AS this Question as multiparts solving first part or you can mention the part  Given data -: 1. dia…

Q: The square deforms into the position shown by the dashed lines in. The dimensions are S=49 mm, S′=54…

A: Given data- S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mmDetermine-A) the shear strain at A relative to…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: at each of those points. Write each state of stress in the form of a tensor, observing the z-y-…

A:

Q: If A and B are both made of wood and are 3 8 in. thick, determine to the nearest 14 in. the smallest…

A: Provided that both the elements A and B are 3/8 inch thick. The applied force of 800 lb will have…

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: Determine the average shear stress in the tube if the dimension a = 200 mm

A:

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: Determine the maximum w that can be applied if the shear stress limit is 100 MPa. Then determine the…

A:

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: If M=2.5kip.ft, determine the magnitute of the resultant force the bending stresses produce on the…

A:

Q: The following shaft consists of a tube AB and a solid rod BC. The tube has an inner diameter of 25…

A: Please check sign convention I took compressive as negative.If you have any doubts please comment

Q: find the average shear stress on the section of the inclined member if we were to cut it…

A:

Q: 1-63.M. The key in Figure 1-18 has the dimensions b= 10 min, h = 8 mm, and L= 22 min. Determine the…

A: Given:b = 10 mmh = 8 mmL = 22 mmTorque transferred, T = 95 N.m or 95000 N.mmShaft diameter, d = 35…

Basics of Mechanical Engineering Design

The word mechanical engineering design consists of two words, mechanical engineering, and engineering design. Mechanical engineering deals with the design and analysis of mechanical systems and components using the laws and principles of mechanics and physics. On the other hand, engineering design deals with determining the dimensions of the components or members under the action of external influences such as loads to make it fail-safe. Engineering also deals with determining the maximum and safe limit of loads and stresses that can be exerted on a body without causing the component to fail. In the domain of mechanical engineering, design is restricted to determining the permissible safe dimensions and loads that can be applied to the component without causing it to undergo fractures or deformations. Mechanical engineers are primarily in charge of the design and analysis of the mechanical components of a system under static and dynamic conditions.