In the system given in the figure, the flow rate of the current passing through the AC pipe is how many (liters/Second)LT/s. Other data are given in the table. Points B and C are open to the atmosphere, from the reference plane of these points Heights from are also given in the table. Pipe Pipe Length (m) diameter (mm) coefficient Pipe Darcy Friction АВ 1000 250 0,016 AC 800 200 0,016 |QGiren(m /s) 200 ZB(m) 50 Zc (m) 20 B QB QGiren A

In the system given in the figure, the flow rate of the current passing through the AC pipe is how many (liters/Second)LT/s. Other data are given in the table. Points B and C are open to the atmosphere, from the reference plane of these points Heights from are also given in the table. Pipe Pipe Length (m) diameter (mm) coefficient Pipe Darcy Friction АВ 1000 250 0,016 AC 800 200 0,016 |QGiren(m /s) 200 ZB(m) 50 Zc (m) 20 B QB QGiren A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the network given in the figure, the flow rate of the current passing through the BE pipe is how many (liters/Second)LT/s. Other data for the network are given in the table. K values given in the table, K = fL / (29DA2) using the formula and length size in meters, Time size in seconds have been calculated. Qc QE QB K KCD KDE KDF KBe (LT / S) (LT/S) (LT/S) 2000 2500 2000 3000 3000 600 100 200 Kcd KOF -bile Koe Кве
The head loss due to flow of a fluid inside a pipe is calculated from .L V? D 2g h Loss where Loss f = friction factor L = pipe length (m) D = pipe diameter (m) V = average flow velocity (m/s) g = acceleration due to gravity (m/s²) What is the appropriate unit for friction factor f?
Give the reason behind the followings: 1- All gases can be considered as compressible fluids. 2- The force at a surface at rest with respect to the fluid must act normal to the surface. 3- Mercury is always used in the manometer. 4- Piczometers cannot be used to measure the vacuum (negative) pressures of liquids 5. The viscosity of all liquids decrease with increasing in temperature
2. Two systems of forces are shown in the figure below. Are they equivalent? Show your entire calculatio ns. 100N 200 N 1.5m 1.5m 100 N 500 N.m 1.5m 1.5m 300 N.M 200N System 1 System 2
The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L₁ = 3 ft, L₂ = 0.5 ft, and L3= 1.25 ft. The densities of the oil and mercury are 55 and 845, respectively, each in lb/ft³. Let g = 32.2 ft/s². Pgage = i Pressure gage lbf/in.2 Air Determine the reading of the pressure gage, in lbf/in.2 (gage). Oil (p=55 lb/ft³) Pam Mercury (p=845 lb/ft³) g=32.2 ft/s²
A venturimeter as shown in the figure (not to scale) is connected to measure the flow of water in a vertical pipe of 20 cm diameter. ←Pipe diameter = 20 cm Throat diameter = 10cm 30cm 15 cm Mercury Specific gravity = 13.6 Assume g = 9.8 m/s². When the deflection in the mercury manometer is 15 cm, the flow rate (in Ips, round off to two decimal places) considering no loss in the venturimeter is
Fluid Mechanics Given: A square tank (open to the Atm) holds 3 feet of oil on top of 6 feet of water. An outlet pipe that is 2 inches in diameter provides an outlet for the water. The outlet is located 2 feet above the bottom of the tank. Find: Neglecting friction energy loss, determine the discharge of water out of the tank. The specific gravity of the oil is 0.86.
Topic: Flow in closed conduits For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a friction factor of 0.020 Which of the following statements is FALSE? *The inflow in pipe 1 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 4 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 3 is equal to the inflow as well as the outflow. *The inflow in pipe 1 is equal to the outflow in pipe 5 Please answer with complete and detailed solution. ASAP. Thank you
In the given image, the pressure at point A is 29 lbf/in2. All fluids are at 20°C. What is the air pressure in the closed chamber B, in Pa Numeric Response Water SAE 30 oil 4 cm 3 cm 6 cm 3 cm Air B Liquid, SG= 1.45 5 cm 8
The fluid 1 in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in figure below. Determine the gage pressure (in kPa) of air in the tank if hj=2.1m, h2=2.9m and h3=1.3m. Take the densities of fluid 1, fluid 2 and fluid 3 to be 1906 kg/m³, 1173kg/m³ and 27357kg/m³, respectively. fluid 2 Air hị fluid 1 h2 h3 fluid 3 2.
A venturimeter as shown in the figure (not to scale) is connected to measure the flow of water in a vertical pipe of 20 cm diameter. Pipe diameter = 20 cm Throat diameter = 10 cm 30 cm T 15 cm Mercury specific gravity = 13.6 Assume g = 9.8 m/s². When the deflection in the mercury manometer is 15 cm, the flow rate (in lps, round off to two decimal places) considering no loss in the venturimeter
Please solve it correctly I can't ask same question again and again