pressurized by air, and the pressure is measured by a multifluid manometer as shown in figure below. Determine the gage pressure (in kPa) of air in the tank if hj=2.1m, h2=2.9m and h3=1.3m. Take the densities of fluid 1, fluid 2 and fluid 3 to be 1906 kg/m³, 1173kg/m³ and 27357kg/m³, respectively. fluid 2

pressurized by air, and the pressure is measured by a multifluid manometer as shown in figure below. Determine the gage pressure (in kPa) of air in the tank if hj=2.1m, h2=2.9m and h3=1.3m. Take the densities of fluid 1, fluid 2 and fluid 3 to be 1906 kg/m³, 1173kg/m³ and 27357kg/m³, respectively. fluid 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
2
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown. The tank is located on a mountain at an altitude of 1400m where the atmospheric pressure is 89.6 kPa. Determine the pressure of air in the tank if h1 = 0.5m, h2 = 0.5m, and h3 = 0.6m. Take the densities of water, oil and mercury to be 1000kg/.850 kg/and 13,600 kg/
Given The tank shown has one curved surface restraining a body of static fluid, with the following dimensions: w- 5.00 m h1 = 2.5 m R1 = 0.85 m Required Determine the value of x-bar in metres, to the nearest 1000th. Water hl R1
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in the Figure Qla with fluid levels of: h1=0.4 m, h2=0.5 m and h3=0.6 m. Take the densities of water, oil and mercury to be 1000 kg/m³, 850 kg/m³ and 13600 kg/m³ respectively. oil h1 Water h3 h2 Mercury Figure Q1a a) What is the gauge pressure at point 1, the surface of the water in the tank? b) In deriving the Darcy-Weisbach equation it was found that there is a direct relationship between the pressure drop experienced due to friction along a pipe with its length. Using dimensional analysis determine an expression for this pressure drop assuming that it is also a function of the pipe diameter in inches, fluid density and velocity. c) Assuming incompressible flow and that complete mixing occurs between the two inflows shown in Figure Q1c before the mixture discharges from the pipe at D. Determine for the fluid at D: i- The mass flow rate The density The velocity i- i- UFMFGS-15-…
Q 1 A
Not sure how to do this one. Would appreciate a full solution, thanks!
please show all the solution and write down on a paper so that i can understand.. Thank you so much
Refer to the picture below to solve the following problems
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +