In the network given in the figure, the flow rate of the current passing through the BE pipe is how many (liters/Second)LT/s. Other data for the network are given in the table. K values given in the table, K = fL / (29DA2) using the formula and length size in meters, Time size in seconds have been calculated. QE QB K KCD KDE KDF Kee Qc (LT / S) (LT/S) (LT/S) 2000 2500 2000 3000 3000 600 100 200

In the network given in the figure, the flow rate of the current passing through the BE pipe is how many (liters/Second)LT/s. Other data for the network are given in the table. K values given in the table, K = fL / (29DA2) using the formula and length size in meters, Time size in seconds have been calculated. QE QB K KCD KDE KDF Kee Qc (LT / S) (LT/S) (LT/S) 2000 2500 2000 3000 3000 600 100 200

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through an expansion pipe as illustrated in Figure 1. Q ((A) S 2 m v(s) (B) Figure 1: Schematic of water flowing through an expansion pipe. The velocity along streamline s is given by v = = 2t(3 s) m s-¹ where t is in seconds and s is in meters. Assuming viscous effects are negligible, (a) Derive an expression for change in velocity with respect to time. (b) Derive an expression for change in velocity with respect to space. (c) At the instant t = 2 seconds, if the pressure as point A is 20 kPa, determine the pressure gradient, d, needed to produce this flow via application of the Bernoulli equation. (d) What assumption in Bernoulli's equation is clearly violated in this example?
Explain 36. In the figure, water is pumped into an empty right cylindrical water tank of base radius 60 cm and height 100 cm through a right cylindrical water pipe of radius 4 cm. It is given that the speed of water flow is 1.5 m/s. (a) Will the water overflow after 2 minutes? Explain your answer. (b) Suppose water leaks through a small hole at the bottom of the water tank so that the water level drops at a speed of 5 cm per minute. Can the water tank be filled up? Explain your answer. 60 cm 100 cm
The pressure drop of water in a pipe is measured by a manometer using a liquid of density 2000 kg/m³. The difference in height of the liquid in the limbs is 10 cm. Then, the pressure drop is
2. Two systems of forces are shown in the figure below. Are they equivalent? Show your entire calculatio ns. 100N 200 N 1.5m 1.5m 100 N 500 N.m 1.5m 1.5m 300 N.M 200N System 1 System 2
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
The air resistance to the motion of a vehicle is something important that engineers investigate. As you may also know, the drag force acting on a car is determined experimentally by placing the car in a wind tunnel. For a given car, the experimental data is generally represented by a single coefficient that is called the drag coefficient. It is given by the relationship: Fa C, = where C, = drag coefficient F, = measured drag force (Ib) p = air density (slugs/ft') V = air speed inside the wind tunnel (ft/s) A = frontal area of the car (ft²) What is the appropriate unit for C, if the preceding equation is to be homogeneous in units? Show all steps of your work.
I need to solve the question of the fluid
A manometer is attached to a water tank (s=1) as shown in the figure.Find the height of the free water surface above the bottom of the tank in m. Round your answer to 2 decimal places.
Reynold's number is used to determine the type of flow pattern through a pipe. It is defined by the equation where ρ =density, μ = viscosity, V = velocity, D = diameter of pipe. Perform a detailed UNIT ANALYSIS to determine the unit of Reynold's number. State your answer in a complete statement.
The fluid 1 in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in figure below. Determine the gage pressure (in kPa) of air in the tank if hj=2.1m, h2=2.9m and h3=1.3m. Take the densities of fluid 1, fluid 2 and fluid 3 to be 1906 kg/m³, 1173kg/m³ and 27357kg/m³, respectively. fluid 2 Air hị fluid 1 h2 h3 fluid 3 2.
We explained that the electric power consumption of various electricalcomponents can be determined using the following power formula: P = VI = RI2 where P is power in watts, V is the voltage, I is the current in amps, and R is the resistance of the component in ohms.Plot the power consumption of an electrical component with a resistance of 145 ohms. Vary the value of the current from zero to 4 amps. Discuss and plot the change in power consumption as the function of current drawn through the component.
FLUID MECHANICS: THE ENERGY EQUATION: The attached image shows a common consumer product called a water pik. The device uses a motor to drive a piston pump that produces a jet of water (d = 3mm, T = 10oC) with a speed of 25m/s. Estimate the minimum electrical power in Watts that is required by this device. Hints: (a) Assume the power is only used to produce kinetic energy of the water in the jet. (b) In the time interval delta t, the amount of mass that flows out of the nozzle is delta m, and the corresponding amount of kinetic energy is (delta m V2/2)