Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then flows from the tank as a jet of diameter d. Determine the value of d if the water level in the tank remains constant. Viscous effects are negligible. d= ft 3 ft 0.093-ft diameter 1 ft 4 ft 0.15-ft diameter

Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then flows from the tank as a jet of diameter d. Determine the value of d if the water level in the tank remains constant. Viscous effects are negligible. d= ft 3 ft 0.093-ft diameter 1 ft 4 ft 0.15-ft diameter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to (a) 26 cm (c) 76 cm Patm 144.444 Hg= (b) 50 cm (d) 126 cm arter
calculate the value of the force exerted by the water above the window of the dam. Be sure to explain why if the pressure varies from the surface of the water, the lower limit for the integral is taken from depth "a" and not from zero? (it is convenient that you make diagrams to support your answer).
13 PLEASE PROVIDE COMPLETE AND DETAILED SOLUTION
6. From the figure shown. Find the pressure head at A when fluid A is seawater (1.03), Fluid B is (s = 2.87); z = 12 in; y = 8 ft Fluid A Fluid B y Sea water
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
Fluid Mechanics Given: A square tank (open to the Atm) holds 3 feet of oil on top of 6 feet of water. An outlet pipe that is 2 inches in diameter provides an outlet for the water. The outlet is located 2 feet above the bottom of the tank. Find: Neglecting friction energy loss, determine the discharge of water out of the tank. The specific gravity of the oil is 0.86.
The Newtonian fluid shown in is confined between the plate and a fixed surface as shown in (Figure 1). Its velocity profile is defined by u = (8y-0.3y2) mm/s, where y is in mm. The plate has a surface area of 29(10³) mm² in contact with the fluid. Take μ = 0.482 N. s/m². Suppose that h = 6 mm. Figure h < 1 of 1 Part A Determine the force P that must be applied to the plate to cause this motion. Express your answer to three significant figures and include the appropriate units. xa P= 67.1 μA Xb a b X.10n < Return to Assignment mN Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ? Provide Feedback
Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the center of the pipe; the reading of a mercury manometer connected to the pitot is 100 mm. The flow is also measured by a venturi meter which connected with the same mercury manometer and the pressure drop across it equals to 300 mm. Find the ratio of venturi to pipe diameter and determine the pressure drop due to friction across the venturi meter.
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +
A tube of diameter 25 mm is used (as shown in the below figure) as a siphon to discharge water from a large open vessel into a drain at atmospheric pressure, (Given: Atmospheric pressure = 101.325 kPa) ignoring friction losses (3) (1) Determine (a)Velocity of flow through syphon (b)Discharge through the syphon (c)The minimum pressure inside the syphon (2) 160 mm 80 mm, 100 mm
7. Two water tanks are connected to each other through a mercury manometer with inclined tubes, as shown in figure. If the pressure difference between the two tanks is 20 kPa, determine the value of ? in degrees. (2 decimal)