**Problem 1: Tank with Inflow and Outflows**A tank has a single inflow and two outflows as shown in the figure. The water surface in the tank is open to the atmosphere.**Questions:**a. Is the tank in the figure filling or emptying?b. At what rate is the water level rising or falling in the tank?**Diagram Description:**- The diagram shows a tank with water and three pipes.- **Inflow:** There is an inflow pipe with a diameter of 4 inches. The velocity of the inflow is 10 ft/s.- **Outflows:** - The first outflow pipe has a diameter of 3 inches and a velocity of 4 ft/s. - The second outflow pipe has a diameter of 6 inches and a velocity of 7 ft/s.- The tank itself is open to the atmosphere and has a 6 ft diameter.

Answered: Image /qna-images/answer/4eaf774c-e239-40d0-bdf7-cdf9ed491774.jpg

1) A tank has a single inflow and two outflows as shown in the figure. The water surface in the tank is open to the atmosphere. a. Is the tank in the figure filling or emptying? b. At what rate is the water level rising or falling in the tank? 4 in. diameter V= 10 ft/s 6 ft diameter Water V=7 ft/s 3 in. diameter V=4 ft/s 6 in. diameter

1) A tank has a single inflow and two outflows as shown in the figure. The water surface in the tank is open to the atmosphere. a. Is the tank in the figure filling or emptying? b. At what rate is the water level rising or falling in the tank? 4 in. diameter V= 10 ft/s 6 ft diameter Water V=7 ft/s 3 in. diameter V=4 ft/s 6 in. diameter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The diameter of a pipe carrying water changes gradually from 6 inches at a lower point to 18 inches…

Q: Water flows through the Venturi meter as shown in the figure below. The specific gravity of the…

A: Given Data : Specific gravity of the manometer fluid = 1.52 Determine the flow rate in feet cubed…

Q: Example Problem: Venturi meter system. The venturi meter shown in figure blow carries water at 60°C.…

A: P1=PA+γWy+1.18PA-PB=γ0.46-1.18+1.25×γw1.18PA-PBγ=-0.72+1.27×1.18PA-PB9.65=-0.72+1.27×1.18PA-PB9.65=0…

Q: Water circulates at 20 °C (p = 1000 kg/m3) in the form of *Y* of the following figure. The flow rate…

A: Mass flow rate in section 1, Diameter of section 1, Diameter of section 2, Speed in section 3,…

Q: Question- A pressure gauge reads 62.3 kPa and 90 kPa respectively at heights of 7 m and 4 m fitted…

A: Pressure gauge readings at 7 m & 4 m are 62.3 kPa & 90 kPa as shown below- To Find- The…

Q: Notice in the figure, a free jet falling from a nozzle of triangular cross section. After it has…

A: Given:- a=0.19 ft, h=2.7 ft, d=0.11 ft To find:- Volume flow rate

Q: Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then…

Q: water flows through a pipe as shown in the figure. The pressure at points 1.10 cm. If the vertical…

Q: 18. The water in a tank is pressurized by air and the pressure is measured by a multifluid manometer…

Q: As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and…

A: To solve this problem, first we need to calculate the specific gravity. Then the Bernoulli equation…

Q: The water speed coming out on the pipe from a cylindrical tank shelter as in the image beside is (in…

A: The figure is shown below, g=9.81m/s2H=inital height bof water l=length od pipet=time…

Q: 9. A tank as shown in figure below compose of hemispherical at the top, cylinder at the middle and…

A: Diameter of orifice =100mmCd = 0.62other data mentioned in the figureA) Time to drop the water from…

Q: As shown in the figure, a pump draws water from reservoir A (El 25m) and lifts it to reservoir B (El…

A: Given: Q= 0.030m3/s,

Q: Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is…

Q: A pump system is used to move water at a flow rate of 30 L/s from a lower to a higher reservoir in a…

A: Given, D = 150 mm e = 0.3 mm L = 506 m

Q: Find the pressure magnitude in the Gasoline Pipe at the right side of

A: Pressure is represented as vertical height of fluid column P = density of fluid × g ×h Where h =…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

**Problem 1: Tank with Inflow and Outflows**

A tank has a single inflow and two outflows as shown in the figure. The water surface in the tank is open to the atmosphere.

**Questions:**

a. Is the tank in the figure filling or emptying?

b. At what rate is the water level rising or falling in the tank?

**Diagram Description:**

- The diagram shows a tank with water and three pipes.
- **Inflow:** There is an inflow pipe with a diameter of 4 inches. The velocity of the inflow is 10 ft/s.
- **Outflows:**
- The first outflow pipe has a diameter of 3 inches and a velocity of 4 ft/s.
- The second outflow pipe has a diameter of 6 inches and a velocity of 7 ft/s.
- The tank itself is open to the atmosphere and has a 6 ft diameter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q03
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
Fluid Mechanics Given: A square tank (open to the Atm) holds 3 feet of oil on top of 6 feet of water. An outlet pipe that is 2 inches in diameter provides an outlet for the water. The outlet is located 2 feet above the bottom of the tank. Find: Neglecting friction energy loss, determine the discharge of water out of the tank. The specific gravity of the oil is 0.86.
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.