Answered: In determining the time of setting of…

In determining the time of setting of hydraulic cement, tabulate the difference in using the VICAT NEEDLE and GILMORE NEEDLES.

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter11: Pricing Concrete Work

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Related questions

Q: Practical Part Q4). 1- State the meaning of normal consistency of cement. 2- Which method is widely…

A: Cement A dry, powdery material known as cement is created by calcining lime and clay. It can be…

Q: If the required slump is 75 mm and the maximum aggregate size is 22.5 mm, what is the quantity of…

A: Given Data: Slump size = 75mm Aggregate Size = 22.5mm

Q: Using Figure 7.34,a. Determine the ultimate stress at each water–cement ratio.b. Determine the…

A: The stress-strain curve indicates the peak values of the stress and strain values for the different…

Q: What is the modulus of rupture where the sand-lightweight concrete has an f of 4000 psi? (The result…

A: f'c = 4000 psi Modulus of rupture fr = 7.5λf'c λ= 1 for light weight concrete

Q: TABLE P5.21 Sieve Size, mm 25 19 12.5 9.5 4.75 2.36 Amount Retained, g 0 376.7 888.4 506.2 1038.4…

A: Sieve Analysis : To assess the grain size distribution of soils with a diameter higher than 0.075…

Q: Situation 3 A compressive strength test were conducted to the following cylinder, Cylinder 1 3015…

A: Given data, Diameter d = 634 in

Q: Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A…

A: Given, Do = 0.5 in Lo = 2 in

Q: Given that the height of the specimen ring used for the one-dimensional consolidation test was 1…

A: Given,the height of the specimen ring used for the one-dimensional consolidation test was 1 inch and…

Q: Calculate the slump of fresh concrete mix if you know: 1. W/C = 0.47 %3D 2. Sand = 648 Kg/m3. 3.…

A: d1= 0.1 m d2 = 0.2 m h= 0.3 m A1= π/4 x d12 = π/4 x 0.12 A1 = 7.854 x 10-3 m2 A2= π/4 x…

Q: Briefly describe the three forms clay can be found in with supporting examples.

A: Clay are generally form when rock comes in contact with water, air, and strem. There are two types…

Q: Q1) Define the C-S-H phase of cement paste.

A: Note : Since, you have posted multiple questions... we will provide solution for only the first…

Q: 2. By the Volume and Area Method, find the quantity of ce- ment, sand and gravel of the concrete…

A: We have to determine the value of quantity of cement, sand and gravel of the concrete pavement of 4…

Q: 7.43 Three batches of concrete were prepared using the same materials and ingre- dients, except that…

A: Given,

Concept explainers

Types of Cement

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon mixing with water. The water turns the cement compounds into gel-like submicroscopic particles having higher surface areas. It is due to the hydration properties of cement, they are often known as hydraulic cement. For instance, Portland cement is a popular example in this category.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
Portland cement concrete consists of what four primary elements?
Three groups of students from the Geotechnical Engineering class collected soil-aggregate samples for laboratory testing from a recycled aggregate processing plant in Palm Beach County, Florida. Three samples, denoted by Soil A, Soil B, and Soil C, were collected from three locations of the aggregate stockpile, and sieve analyses were conducted (see Figure 2.35). (a) (b) Figure 2.35 (a) Soil-aggregate stockpile; (b) sieve analysis (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida) a. Determine the coefficient of uniformity and the coefficient of gradation for Soils A, B, and C. b. Which one is coarser: Soil A or Soil C? Justify your answer. c. Although the soils are obtained from the same stockpile, why are the curves so different? (Hint: Comment on particle segregation and representative field sampling.) d. Determine the percentages of gravel, sand and fines according to Unified Soil Classification System.
Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
Given the specifications for an asphaltic concrete mixture and the results of a sieve analysis, determine the proportion of different aggregates to obtain the required gradation. Coarse aggregates: 60% Fine aggregates: 35% Filler: 5%
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
For the drilled shaft described in Problem 19.7, estimate the total elastic settlement at working load. Use Eqs. (18.45), (18.47), and (18.48). Assume that Ep = 20 106 kN/m2, s = 0.3, Es = 12 103 kN/m2, = 0.65 and Cp = 0.03. Assume 80% mobilization of skin resistance at working load. (See Part c of Problem 19.7) 19.7 Figure 19.16 shows a drilled shaft without a bell. Here, L1 = 6 m, L2 = 7 m, Ds = 1.5 m, cu(1) = 50 kN/m2, and cu(2) = 75 kN/m2. Find these values: a. The net ultimate point bearing capacity. Use Eqs. (19.23) and (19.24) b. The ultimate skin resistance. Use Eqs. (19.26) and (19.28) c. The working load, Qw (FS = 3) FIG. 19.16