I Review The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.

I Review The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Both ends of the beam are guided or slider support not Fixed support. Plz, solve this problem using stiffness Method and show all the step and alsi draw SFD and BMD My last two digits of my reg.no: 95 Structural Analysis-2
Could I please get a full written solution on how to answer question 6 for this past paper question please?
Current Attempt in Progress The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.25 in., -0.65 in.). Assume a = 7 ft, b = 5 ft, and h = 6 ft. Determine the normal strain in each %3D bar. a A y h B Answers: EAB %3D EBC
Q 2. For the symmetrical section in figure 2 shown below, calculate B mm 350 mm 0.8 B mm Figure (2) (i) The elastic section modulus (Z) (ii) The Plastic section modulus (Zr) (iii) Shape factor (S) (iv) Plastic moment given fy- 262 N/mm2 B= 202
Question 6 of 11 -/10 E View Policies Current Attempt in Progress The stresses shown in the figure act at a point on the free surface of a machine component. If o= 45 MPa in the direction shown, determine the normal stress oy at the point. 27 MPa 30° 50 MPa O -16.3 MPa O -19.5 MPa O-22.8 MPa O-17.2 MPa O -20.5 MPa Attempts: 0 of 1 used Submit Answer Save for Later
QUESTION 4: Check whether the beam section whose loading condition, cross section and dimensions are given in the figure is sufficient. Also draw the shear stress diagram of the section next to the section.
in (Eigure 1), the forces in members A and Care FA = 6.5 kN and Fc = 3 kN. The force system is concurrent at point O. Determine the forces acting on members B and D that are required for equilibrium. Fo Part A 45 Submit FB = Value Part B Determine FB. Express your answer to three significant figures and include the appropriate units. μA Request Answer BASED 60" Units B FB Determine FD. Express your answer to three significant figures and include the appropriate units.
A horizontal force of P = 50 kN is applied to joint C as shown in (Figure 1). Each pin has a diameter of 25 mm and is subjected to double shear Figure 1.5 m 2m Part A Determine the maximum average shear stress in pin A of the truss. Express your answer to three significant figures and include the appropriate units. (Tavg) A = Submit HA Value 4 d Units Previous Answers Request Answer F ? X Incorrect; Try Again; 5 attempts remaining Check that you have converted between SI units correctly. D
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
Vn = 6*36*1/(4*1.1) = 49.09 am I wrong? I believe in the calculation in the solution the coefficient m was not taken into account. And Pn is not 54 kips either, with the given formula it comes up as 6*36*0.5/(4*1.25) = 21.6 and in which case the design strength would be 21.6 kips. Please let me know if there's something I'm missing from the formulas.
Q3: Figure (3) shows a punching machine of plate (thickness 2 mm).Punching operation is applying many times to make thousands holes (d-4 mm) through cam (2) which attaches with the ram (1) from two sides and moves it up and lowering down by action of weight (1000N). Assume the ram (1) is circular cross section. Requirement: Select the correct answer of following: 1. The ram (1) subjected to static bending stress at section (X-X): 1800ND Flgure (3) X- B. 100 mm A: True B: False 2. The ram (1) subjected to reversed load at section (Y-Y): B. False 3. The diameter of ram (1) at section (X-X) is (44603 mm): B: False 1- A: True A: True 4. The diameter of ram (1) al section (Y-Y) is (9.694 mm): B: False A: True For ram (1) and pin (b): S,-160 MPa S,-210MPA S-100MPA 5. The torque required to rotate cam (2) is (10000 N.mm): A: True B: False 6. The plate material can be punched by this mechanism has (S,-39.788 MPa): N= 2.5 A: True 7. The diameter of pin (b) on the ram (1) is (6.307 mm): B: False…
Current Attempt in Progress The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load Pis applied, joint B moves to the coordinate position (0.35 in., -0.45 in.). Assume a = 10 ft, b = 7 ft, and h = 8 ft. Determine the normal strain in each bar. Answers: EAB 3608.10 με EBC= 8577.01 pe