If the wire has a diameter of 0.9 in., determine how much it stretches when a horizontal force of 2.5 kip acts on the pole Express your answer to three significant figures and include appropriate units. SAB= 0.012 μÅ in BA ?

Q: n engineer was assigned to measure a rectangular lot. There are two available tapes hat he can use,…

A:

Q: Define the term capillary fringe.

A: The capillary fringe is characterized as the saturated zone of water immediately just above the…

Q: Hw Lar the Soil Set Showwn, Soilo 30 cm Olt, lo, he @all ponts 36 Cm 10 10 cm O Pw.P @ Ports B,…

A:

Q: P.-P. (1+1)" WD. - P.x Cxt+ WD P-0.SCApu A 60 MLD water treatment plant has 4 mechanical…

A:

Q: Draw I.L for RA, Re RF, VB, VcL, VERI Vo. MA, Mc M0 4 3.

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 32 3" fo=3000 ps fy= NWC = Mn=?, Tied bars. 28 = 60 ksi 多#9 14

A:

Q: Mmax <=

A:

Q: Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation…

A: Data Given: Bulks after excavation = 10% Shrink = 12% Chainage distance = 100m Asked: Draw Mass…

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: QUESTION TwO (a) Determine the side widths and areas of the following cross sections:- Fill section…

A: Given : Fill section consisting sides with slopes 1 in 3 and 1 in 3 Bottom side 1 in 10 Central…

Q: 10 ft 5 ft 1 Az 3 ft Z Ay A 2 ft 8 ft 12 k D B₂ 6 k B Cy C₂/C By Bx Cx 7 ft / 4 ft --- X

A: This truss which we are solving is a space Truss. A space truss is used in the three-dimensional…

Q: Define The width of the loaded area

A: Load: It is defined as the weight or force which is applied on the member, joint, or anybody which…

Q: 50 ↓ 50² 50k $50* a M b 6 at 25 ft 150 ft 50k 25 ft PROBLEM: DETERMINE a,b,AND C BY METHOD OF…

A:

Q: What is Dimension D? Setback = 0.252, Bend Allowance = 0.345

A: The given values are as follows,The set back =0.252The Bend allowance=0.345To determine The…

Q: 405 E= 200 CDA I= 19 X 10 4. A 2m 4m at C. C P. the to teation S'D. Ball Pen 1423

A:

Q: f=35 Mpa Pe-68AN by -35 Mpa Find sec. dimensionsLAS

A: Solution:- Given data fc=35 MPa, andfy=350 MPa To find , sectional dimension and area of steel =?…

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: PRACTICE PROBLEM 1- Find the length of Flat A. SETBACK- R•T BEND ALLOWANCE- 2n{R• 1/2T) 6" 3/16" R.…

A: We have to find the value of length of the flat A according to the given data like as given in the…

Q: An 8m steel tape was purchased and advertised as follows: Standard temperature : 24°C Standard Pull…

A:

Q: Name this force system         Question 19 options:   Non-planar parallel…

A: Given a system of force system

Q: Please Create section AA' and BB' on autocad.

A: We need to first obtain the 3D model of given drawing using the following steps and then create…

Q: The cross section at station 2+60 has a cut area of 9 ft² and a fill area of 4 ft² and the cross…

A: Given that,  Cut Area of cross-section at station 2+60, A2+60=9ft² Cut Area of cross-section at…

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: diagram. 10kN.m 2m 3m (20+#ID)/2 KN 2m 5m 77 5kN/m B

A:

Q: How is shear starin rate calculated?

A: Strain rate is defined as the change in the strain or the deformation of a particular material with…

Q: 100. The positional tolerance of the hole documented below is most nearly: Ø50 +0.5 -0.3 OA. OB. O…

A: As we know,Maximum Material Condition (MMC) Method

Q: Describe the TRD method.

A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…

Q: Situation 1] A private parcel was surveyed prior to the construction of a proposed fabrication…

A: Given Table: By putting X=6, Y=6, Z=3

Q: Which shortcut key lets you draw a line? O RO O z TB

A:

Q: Problem 3 Compute the nominal compressive strength of the member shown. Use the theoretical value…

A: Given Data:Member HP 16×121                        A572 Grade 55Length of member = 14 feet To…

Q: # Fores Pand F aching alog the bar sham in the 5., defermine Pand F to mainteanilibraum. (2m 350H-…

A: Since, you have posted multiple questions we will solve only the first question... Kindly repost the…

Q: Name this force system Question 17 options: Non-planar concurrent Coplanar…

A:

Q: 24" 4 #8 12" #4 at 9"0.c. fé= 4000 psi" NWC. & Mn = ? Grade 60 steel. Tied Bars.

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: Using  simpson's 1/3 and 3/8 ruel. Use 5 panels

A:

Q: Calculate the volumes formed between the two mixed cross-sections given in the figure.  (L= 30m)

A: Find the areas of cut and fill A1 (fill) Area A1 = Area of trapezium –Area of triangle…

Q: izin 12 in 12 jan ELEVATION 1.5 id. W 14 X 90 2L3X2 X 1/2 SECTION

A: a)  To determine the design strength First calculate the net area of double -angle bar

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.