Current Attempt in Progress The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load Pis applied, joint B moves to the coordinate position (0.35 in., -0.45 in.). Assume a = 10 ft, b = 7 ft, and h = 8 ft. Determine the normal strain in each bar. B.

Current Attempt in Progress The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load Pis applied, joint B moves to the coordinate position (0.35 in., -0.45 in.). Assume a = 10 ft, b = 7 ft, and h = 8 ft. Determine the normal strain in each bar. B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=2.0 m, LBc=6.9 m, P=19 kN, bf=180 mm, t₁=14 mm, tw=9 mm, d=159 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. A Answers: OmaxT maxC = LAB i i P B LBC bf + Cross section MPa MPa P LCD D X
The light rigid bar ABCD shown is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 30 kips is applied.
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.46 in., -0.20 in.). Assume a = 15 ft, b = 30 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. A Answer: EAB EBC = i i P a (1) B με με X b (2) C d
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Consider a cantilevered beam which is made of two identical. rectangular sections, a force P is applied at free end. 11) if A and B are not clued together, determine the bending stress distribution at a-a cross section, draw o Chint: each section carries P/ and label the Tout at the outest fibers. * 0.5m a 12) if we weld the two A & B together along the member length. determine the bending stress distribution, draw and laber. m ✓ P=1kw A 181- дет B зст
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
The two bars are used to support load P. When unloaded, joint B has coordinates (0,0). After load P is applied, joint B moves to the coordinate position (-0.65 in., -0.10 in.). Assume a = 20 ft, b = 40 ft, c = 14 ft, and d = 28 ft. Determine the normal strain in each bar. a b C (2) (1) Answer: EAB = i &BC= i P B με με d