Item 4(Figure 1)Figure 1Wof 1<(200x²) N/m200x²) N/-W =Lammur9 m600 N/m>XPart AReplace the loading by an equivalentforce.Express your answer to threesignificant figures and include theappropriate units.FRSubmitPart BμÅValue UnitsMROReplace the loading by a couple momentacting at point O.Express your answer to threesignificant figures and include theappropriate units.=My Answers Give UpHÅ?ValueUnits?

Answered: Part A Replace the loading by an…

Part A Replace the loading by an equivalent force. Express your answer to three significant figures and include the appropriate units. U μÀ

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A crate weighs 655 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 48 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom cc i❀O ↑Z CC BY NC SA a b с с 6 The tension in rope AC is 조 Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 44 in 35 in 12.1 in The tension in rope AB is The tension in rope AD is χ lb lb a lb D
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.
The maximum allowable tensile force in the members of the truss is (Ft)max = 1700 lb, and the maximum allowable compressive force is (Fe)max = 1000 lb. (Figure 1) Figure 1 of 1 Part A Determine the maximum magnitude P of the two loads that can be applied to the truss. Take a = 8 ft. Express your answer in pounds to three significant figures. P = Submit Provide Feedback Π| ΑΣΦ ↓↑ vec Request Answer C ? lb
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?
H.W.# 2: Find the value of force (P) shown in figure if you know that the middle part of the rigidly fastened shaft is stressed to 400 Mia of tensile stress. Then calculate the stress in each of the other two end parts. = 40 mm² 10 kN A = 80 mm² A = 40 mm² 22 KN
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is an inverted T with a 1'' by 8'' stem and a 1'' by 4'' base, as shown. The cross section has a moment of inertia of 97 in4 and its neutral axis is given. Pay attention to units, and calculate your answer to 1 decimal place. Determine the allowable maximum bending moment of the beam based on the allowable bending stress in tension, M allow: ____ kip-in.
Item 7 The members of the truss are assumed to be pin connected. (Figure 1) Figure 1 of 1 12 ft 44 -16 ft 16 ft P P 16 ft Part A If member AB is an A992 steel rod of radius 2.5 in., determine the maximum load P that can be supported by the truss without causing the member to buckle. Express your answer to three significant figures and include the appropriate units. μА P = Value kip Submit My Answers Give Up ?
in (Eigure 1), the forces in members A and Care FA = 6.5 kN and Fc = 3 kN. The force system is concurrent at point O. Determine the forces acting on members B and D that are required for equilibrium. Fo Part A 45 Submit FB = Value Part B Determine FB. Express your answer to three significant figures and include the appropriate units. μA Request Answer BASED 60" Units B FB Determine FD. Express your answer to three significant figures and include the appropriate units.
Replace the loading acting on the frame by an equivalent resultant force and specify where the resultant's line of action intersects member AB (Figure 1). Suppose that F₁ = 200 lb, F2 = 100 lb, and M = 400 lb. ft. Figure x F₂ M 30⁰ -3 ft B 2 ft 4 ft 1 of 1 Determine the magnitude of the resultant force. Express your answer in pounds to three significant figures. FR = Submit Part B 0 = Submit Part C Determine the angle between the resultant force and the x axis. Express your answer in degrees to three significant figures. y = ΠΑΣΦ Submit Provide Feedback Request Answer ↓↑ ΑΣΦ Request Answer ΑΣΦ vec ↓↑ vec Specify where the resultant's line of action intersects member AB, measured from A. Express your answer in feet to three significant figures. Request Answer ? vec ? lb O , measured counterclockwise from the positive x axis ft below A
The adjacent sketch indicates a brass wire which is exactly 12.00 m long and a steel wire which is 12.01 m long. Each wire has a cross-sectional area of 150 mm2 . What load does each wire carry if E steel = 200,000 MPa & E brass = 110,000 MPa? (Hint: no load on steel wire until brass wire stretches by 10mm, then ratio of stresses in each wire is same as ratio of E v
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z