a=4b=1 b,= 10.1 in1,=0.855 inThe variables a and b are defined by the last twodigits of your Z-number. For example, the Z-numberZ21172743 has a = 4 and b = 3.A992 steelL = (10 + a) inchesA, = (11.7+ 0.1b) in?L in1. Determine the design strength oP, for theyielding limit state.Ag in?= 1.39 in2. Determine the design strength oP, for therupture limit state.Use Table D3.1 Case 4 for UCheck Umin

Design of Tension member as per IS: 800-2007 Given: A992 steel a= 4; b = 1 so, L = (10+4) =14 in Ag…

b= 10.1 in 1= 0.855 in The variables a and b are defined by the last two digits of your Z-number. For example, the Z-number Z21172743 has a = 4 and b = 3. A992 steel L= (10 + a) inches Ag = (11.7 + 0.1b) in? L in 1. Determine the design strength qP, for the yielding limit state. A, in? -1.39 in 2. Determine the design strength qP, for the rupture limit state. Use Table D3.1 Case 4 for U Check Umin

b= 10.1 in 1= 0.855 in The variables a and b are defined by the last two digits of your Z-number. For example, the Z-number Z21172743 has a = 4 and b = 3. A992 steel L= (10 + a) inches Ag = (11.7 + 0.1b) in? L in 1. Determine the design strength qP, for the yielding limit state. A, in? -1.39 in 2. Determine the design strength qP, for the rupture limit state. Use Table D3.1 Case 4 for U Check Umin

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the reference system, determines a coordinate of the centroid Ycg of the symmetrical plane figure. To do so, adopt the value of L = 10·a + 20·(b + 2·c) {mm} as 100. Consider a minimum precision of 6 digits for differences. (a = 7; b=1 ; c=1) Ycg=
1) Derive the ff: (show the relationship or transformation) a) Ym = w a) ym² co pursu upel sugupers LONGE ▷ ▸ to dry unit weight, Yd= atinueu GAR OUR TO DOS Ym ene+Mc IMC
Question 5 Given the function 2x3 – 4x2 – 1 = 0, a root is from the x = 2 and x = 3. Newton-Raphson method to estimate the root correct to 3 decimal places. You must show your working. Solution must be attached at HERE.
2 31 If A = 1 2 4 05 7 What is the cofactor of the second row, third column element? A. B. C. 3 1 D. ल फ ल क Oन्E.
If A = 75°, C = 37° and b = 6, work out the length of a. B® a C (C b
Both parts. Thank You
Find FBC, FBD, FDE, FAB, FBE, FEA, and FCD Show the complete calculation
Determine the force (P) required to keep the block to move up, given that us = 0.32 and uk = 0.29. F1 = 602 and e = 15 *Type your answer in two (2) decimal places without the unit. F1
If S = {0, 1, 2, 3, 4, 5, 6, 7, 8, 9} Event A = {0, 2, 4, 6, 8} Event B = {1,3, 5, 7, 9} Event C = {2, 3, 4, 5} Event D = {1,6, 7} Find: A U C- An B- C" = (C' n D) U B= Sn C'= Ancn D-
21 B -32 C D Z2 ▼ Part B As shown, a system of cables supports a bucket. (Figure 2) The dimensions in the figure are as follows: ₁ -5.25 ft, 2 = 1.40 ft. y₁=2.20 ft. 3/2=4.50 ft. 2₁ = 3.25 and 22 = 2.30 ft. If the bucket and its contents have a combined weight of W = 11.5 lb, determine TA. TB. and Tc. the tensions in cable segments DA, DB, and DC, respectively. Express your answers numerically in pounds to three significant figures separated by commas. ▸ View Available Hint(s) TA TB.TC Submit 175) ΑΣΦ | 41 Previous Answers Provide Feedback X Incorrect; Try Again; 4 attempts remaining. Part C Complete previous part(s) vec 6 0 BOA ? lb
F AE= ? F DE=? F BE=?
A compound shaft consists of segment (1), which has a diameter of 1.9 in., and segment (2), which has a diameter of 2.3 in. The shaft is subjected to a tensile axial load of P = 22 kips and torques TA = 8 kip-in. and Tg = 33 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point Hand (b) point K. For each point, show the stresses on a stress element. P TA (1) H N TB B (2) K C