Activity 1: Read with understanding and solve the following problem carefully and honestly: Write your solution on a separate sheet of paper. 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If the allowable stresses are 140 MPa for bearing in the plate material and 80 MPa for shearing of the rivet, determine the minimum thickness of each plate. (Ans. t = 9 mm) b. Under the conditions specified in part (a), what is the largest average tensile stress in the plates? (Ans. Õ; = 34.91 MPa) %3D

Activity 1: Read with understanding and solve the following problem carefully and honestly: Write your solution on a separate sheet of paper. 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If the allowable stresses are 140 MPa for bearing in the plate material and 80 MPa for shearing of the rivet, determine the minimum thickness of each plate. (Ans. t = 9 mm) b. Under the conditions specified in part (a), what is the largest average tensile stress in the plates? (Ans. Õ; = 34.91 MPa) %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please draw a simple restaurant plan by using autocad. thank you.
I need a quick solution within 15 minutes
Define Soil Contamination.
Suppose you are assigned to construct a clean room. Design a plan layout for clean room, describing all the areas. Please answer at your own words.
How to identify the hazardous and safe places in your home?
Instruction: On a separate short bond paper with 1-inch by 1-inch margin, copy and answer each problem and box your final answer(s). ALl necessary solution must be included. Please consider at least 3 decimal places for the accuracy of your answer. Everything must be hand written and avoid too much erasures. The submission of this plate is one (1) week after the week intended for the topic. 1. Determine the Degree of Freedom of the following Structure 7 k 14 k 14 k 7k 2k J. 6 ft B 8 ft 8 ft 8 ft
Question#1: Make a proposal on PowerPoint comprising only 6 slides. It should include all the important parts of a proposal. Select any topic you like(which is related to civil engineering). Note# Honorable expert teacher kindly give the answer of Q#1 in ppt slide form or take screenshoot from ppt file(after making ppt file) as soon as possible, its urgent for today..i will be very thankful to u for this kind favor. Course; is TECHNICAL REPORT WRITING & ITS PRESENTATION...( Department; Civil engineering department )
Instruction: On a separate short bond paper with 1-inch by 1-inch margin, copy and answer each problem and box your final answer(s). All necessary solution must be included. Please consider at least 3 decimal places for the accuracy of your answer. Everything must be hand written and avoid too much erasures. The submission of this plate is one (1) week after the week intended for the topic. 1. Determine the Degree of Freedom of the following Structure 20 kN 15 kN 10 kN E 10 ft D. 2 m 10 ft- 10ft 10 ft 10 ft 10 k 15 k 5k 2m m
Draw an arrow diagram network for the following project. Activity Description Predecessors Activity A Insulate floor 1 Insulate floor 2 BCDE D F G H I J K L Drywall floor 1 Paint floor 1 Insulate floor 3 Drywall floor 2 Paint floor2 Insulate floor 4 Drywall floor 3 Paint floor 3 Drywall floor 4 Pain floor 4 A A C B B. C D, F E E, F G, I H, I J, K
Interpret plumbing supply and DWV system design and detailing information.
What is stop notice?When can be it used?
What is the checkoff list?