Gasoline flows from a 0.3 m diameter pipe in which the pressure is 300 kPa into a 0.15 m diameter pipe in which the pressure is 120 kPa. If the pipes are horizontal and viscous effects are negligible, determine the flow rate. The specific weight for Gasolin is y=pg = 6.67 Note: The flow rate is given by Q = A₁V₁ = A₂V₂ kN m³

Gasoline flows from a 0.3 m diameter pipe in which the pressure is 300 kPa into a 0.15 m diameter pipe in which the pressure is 120 kPa. If the pipes are horizontal and viscous effects are negligible, determine the flow rate. The specific weight for Gasolin is y=pg = 6.67 Note: The flow rate is given by Q = A₁V₁ = A₂V₂ kN m³

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows initially from tank A to B through a single pipeline which is 150 mm in diameter and 150 m in length, shown in the figure below. Further development requires that the flow rate is to be increased by 30 % by installing a second pipe in parallel, indicated by the dotted line and 82 m in length, running from A to c. The coefficient of friction for each pipe is 0,015. Determine the diameter of this new pipe. = ? L= 82 m 4 m 0 = 150 mm L= 80 m = 150 mm L = 70 m
Question 2 An incompressible fluid flows steadily in the entrance region of a circular tube of radius R = 75 mm. The flow rate is Q = 0.1 m/s. Find the uniform velocity U at the entrance. The velocity distribution at a section downstream is น umax 1-(+)² 2 Evaluate the maximum velocity at the downstream section. Calculate the pressure drop that would exist in the channel if viscous friction at the walls could be neglected L. U1 p = 850 kg/m³ R
At 4C, water has a density of 1000kg/m3 and a viscosity of 1.60 cP. It is to flow through a horizontal commercial steel pipe with a length of 300 m at the rate of 130 gal/min. A head of water of 6 m is available to overcome the friction loss due to skin. What is the pipe's diameter
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
Your team is designing a chemical processing plant. You are the liquid handling and transportation specialist, and you need to transport a solvent (μ = 3.1 cP, ρ = 122k kg/m3) from a storage tank to a reaction vessel. Due to other equipment constraints, the fluid velocity must be 0.8 m/sec, and you must use stainless steel piping (ε = 0.00015 mm) with a total length (L) of 12 m. Determine the pipe inner diameter (ID) you will need to achieve a pressure drop of 0.3 kPa. Use the Moody chart.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Oil of specific gravity 0.8 flows through a pipe of 0.25 m diameter. An orifice of 0.1 m diameter is fitted to the pipe to measure the flow rate. A mercury manometer fitted across the orifice records a reading of 0.8 m. Calculate the coefficient of discharge of the orifice meter if the flow rate measured by it is 0.082 m3/s.
Task 5 A liquid of a density @ flows through a pipe of a diameter d from a tank of a diameter D P. (with pressure p.) to another tank with significantly larger diameter (with pressure PB). Determine the mass flow rate ṁ of the liquid flow and the pressure in the point C. OD D = 60 mm H= 1.2 m Ps = 110 kPa h Given: d= 40 mm h = 0.3 m PA = 1.05 bar P= 1000 kg/m m, Pc od Find: n = 5.73 kg/s pc = 108.4 kPa
Given the 0.063 m length of the syringe. F=1N a. provide an equation to calculate its water flow rate if water is going to travel from a 0.063 m length of syringe with dextrose tube length of 0.5 meter to another 0.063 m syringe (see attached photo). The Inner diameter of the syringe is 0.02. While the inner diameter of dextrose tube is 0.003. b. provide an equation in order to calculate the maximum force or pressure that exerts in plunger in order to travel the water at its maximum speed.
Water enters a house through a pipe with an inside diameter of 20 mm at an absolute pressure of 4 ATM. A 10 mm diameter pipe leads to a second-floor bathroom 5.0 m above. When the flow speed at the inlet pipe is 4 m/s, (a) Find the speed of the water flow and pressure in the bathroom. (b) Find the volume flow rate in the bathroom. (c) What is the horse power rating of the motor pump at the inlet pipe needed? Assuming 60% Efficiency.
A pitot tube is inserted into an air flow to measure the flow speed to measure flow speed. The Pitot tube is inserted into a 100mm diameter tube so that it points upstream into the flow and the pressure as show in figure 5 where p0 = stagnation point. The static pressure is measured at the same location in the flow, using a U-tube differential manometer. Consider density of air equal to 2.3kg/m3 and determine the air flow rate.
The pressure drop in a horizontal commercial steel pipe should not exceed 1 psi per 150 feet of pipe length for flow rates up to 500 gal/min. If the water temperature is never below 50 F°, determine the necessary pipe diameter.