6 m^3/min of 15.6°C SAE 30 is to be pumped from a tank through 40 meters of horizontal pipe; the oil will exit the pipe to the atmosphere. The pump’s push on the oil can create a gage pressure of 38.7 kPa at the horizontal pipe inlet. What minimum pipe diameter should be selected?

Q: 1) At the instant the valve is opened, the Venturi meter indicates a pressure difference of 735 kPa.…

A:

Q: What is the diameter, in millimeter, of an orifice in a tank with a cross-section of 1.5 m? if the…

A: Given data, Point 1 is taken for tank Point 2 is taken for orifice Cross-section of the tank, A1 =…

Q: Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the…

A:

Q: Question 4. The flowrate of the flow is 0,2 m³/s in a pipe placed on a horizontal plane. The pipe…

A: Let Fx =Force exerted by fluid on pipe in x direction  Fy =Force exerted by fluid on pipe in y…

Q: What is the pipe velocity at point 1? Given the specific gravity of pink liquid S=3.9 and height…

A:

Q: Flow Pump 6-in Schedule 40 4-in Schedule 40 4 in Engine Oil 30 in Mercury (sg =13.54)

A: Calculate the pressure change from point 1 to point 2. P1-ρoilg4 in-ρhgg30 in+ρoilg34…

Q: Problem 5.46 The flow of oil through the pipe is 0.041 m³/s. Take Po = 875 kg/m³ Pw 1000 kg/m³.…

A:

Q: A small, high pressure water jet can be used for cutting various materials. A jet with a speed of…

A: For the solution refer below images.

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

A:

Q: From pump 1.0 m 1.5 m a. Using a vertical bar chart, plot the pressure drop (i.e. P₁-P₂) for these…

A:

Q: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe.…

A: Given   Velocity, V = 82 ft/s Diameter, d = 2 in                  = 0.166 ft Find  Flow rate

Q: Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the…

A:

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given-Data:- To-Find:- Power (W)=?

Q: Problem 3. Outcome 5. Please show all work. Air at standard pressure but with T = 50°C flows through…

A:

Q: In order to measure the air speed in a pipe of radius R, you construct a device which tapers the…

A:

Q: What is the maximum height the higher reservoir can sit and be filled using a fixed-speed pump with…

A: Pump Power, P=114HP=1+0.25=1.25HP=687.50lb.ft/s Pump Efficiency, η=57% Volumetric flow rate,…

Q: 0 oil volume flow rate

A: given:

Q: Water is siphoned from a container as shown in Figure 2. Calculate the volume flowrate at point 2…

A: Given data: height, H = 4 m Diameter of the pipe, D = 50 mm = 0.05 m   To find: Flow rate at point 2…

Q: Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure…

A: Given: The flow rate, Q = 50 l/s The energy added by the pump, H = 10 m

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required  pump power.

Q: It is desired to pump 1000 gal/hr of gasoline (specific gravity of 0.85) at a temperature of 50…

A: Calculate the discharge of the pump in m3/s. Q=1000 gal/hr   =1000 gal/hr1.263×10-6 m3/s1 gal/hr…

Q: For the flow configuration shown, you are required to design a pump station to transfer water from…

A: For designing of any pump station, various types of losses are considered. Losses such as major…

Q: 3. Water flows at the rate of 5 ft/s through an inclined pipe. At point A, where the diameter is 12…

A: Find the pressure at point B

Q: You are working as a trainee engineering in a company ABC, is the leading manufacturing company for…

A:

Q: аз in. IS installed in a 6 in. pipe-line. The pressure at the entrance to the meter is 10 psi gauge…

A: A venturi meter(diameter) =3 ininstalled in =6 inA1V1=A2V2π4×6122×v1=π4×3122×v2v1=0.25 v2v2=4 v1…

Q: Q1: A waterline is composed of three sections A, B, and C. Section A has a 200-mm inside diameter…

A: Given:Inner diameter of section A, DA=200 mm=0.2 mLength of section A, LA=1500 mInner diameter of…

Q: At a flow rate of 20 LPM, What will happen if the 30 seconds is 2.943 kPa, the 60 seconds drops to…

A:

Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…

A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…

Q: Water flows from an elevated storage tank through 1800 ft of smooth pipe to feed a system that…

A: To find: The diameter of the pipe. Given: The flow rate of water is Q=20 gallonmin0.1337 ft31…

Q: In a wastewater treatment plant, Blower supplies air to the sequencing batch reactor. It is…

A: Write the given data. Cpitot=0.98ρair=1.2 kg/m3ρwater=1000 kg/m3hwater=75 mm

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: Suppose it takes ½ hour to fill a 16 ft x 32 ft x 7 ft swimming pool from a 2.0 in. diameter pipe,…

A: Time required to fill the swimming pool, t=12hr=12*3600 seconds=1800 secVolume of the swimming pool,…

Q: Find the difference in pressure head and velocity of flow of an oil through a pipe, when the…

A: Given that H= 110 mm of Hg ;sp. gravity of oil= 0.9 ; Density of oil= ρ= 900 Kg/m3 ;The coefficient…

Q: 5. What is the maximum gas velocity criteria in flow meter assembly for orifice flow meters, and…

A: A flow metre (also known as a flow sensor) is an instrument that is designed to precisely measure…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.