NEED TO FIND CALCULATIONS : SHEERFORCE AND BENDING MOMENTCALCULATIONS WITH DIAGRAM, FIND ALLREACTIONS AND MOMENT USING THEFORCE METHOD.米Need CakulatonsPid all reachons ushgfosce method8.4243ByBx-71.5040.362 mm.Lwad (L)AX AShear foxce and bendingmanent calcula h'ons andTaydrawingdefuchionMaxさ个

Answered: Image /qna-images/answer/83cae14a-23ce-4c74-a4ec-fdc84a9df026.jpg

FORCE AND BENDING MOMENT CALCULATIONS WITH DIAGRAM, FIND ALL REACTIONS AND MOMENT USING THE FORCE METHOD. Need Cakulations Pd all reachons ushg fosce method 8.42 By Bx- 1.504 m 0-362 m wad (L) AK A Shear foxce and bnding manent calcula hons and Dx drawing defuchion Max

FORCE AND BENDING MOMENT CALCULATIONS WITH DIAGRAM, FIND ALL REACTIONS AND MOMENT USING THE FORCE METHOD. Need Cakulations Pd all reachons ushg fosce method 8.42 By Bx- 1.504 m 0-362 m wad (L) AK A Shear foxce and bnding manent calcula hons and Dx drawing defuchion Max

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 13 of 14 - /5 View Policies Current Attempt in Progress Determine the coordinates of the mass center of the welded assembly of uniform slender rods made from the same bar stock. a a 1.36 a Answers: (X, Y, Z) = ( i ) a i i ... II
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
T'he pin is made of a material having a failure shear stress of Tail = 100 MPa. Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of F.S. = 2.5 against shear failure. %3D 80 kN
The steel channel is used to reinforce the wood beam. Determine the maximum stress in the steel and the wood if the beam is subjected to a moment of M=1.2kN.m Est = 200GPa, Ew = 12GPa. 12mm A 3.'S. IO. **** SI TEMININING FEMININ... *** 12mm INI MINI SEUR 5.1.3. TE 2277 *** ....... ---- 175mm 100mm 12mm 1.2kN.m
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Determine the force in each member of the truss loaded as shown below. Indicate whether the members are in tension or compression. Summarize your analysis by filling-up the table shown. 300 kN Summary: 3 m Member Internal Force (KN) B AB E D AE BC 5m 400 kN BE CD CE DE - 3 m-3 m
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
2. Determine the force in each member of the platform truss and state if the members are in tension or compression. Approximate each joint as a pin. 8 kN 16 kN 8 kN 3 т 3 т D. 0 000 3 т F 4 m A 4 m Paint X lite
Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all members is 800 mm². Note: You may use any method 3 m ון 2 - 3 m 4 m 5 m 6 kN Situation 4: Terminologies 1. A structural element that carries a load that is applied transverse (perpendicular) to its length and the top fibers are in compression; the bottom fibers are in tension. 2. A structural element that is composed of smaller structural members typically configured in triangular arrangements. 3. Codes that specify combinations of loads that must be considered in the design of structures in the Philippines? 4. How many equations of equilibrium are there in space structures? 5. These are the forces exerted by supports on the structure and tend to prevent its motion and keep it in equilibrium. 6. The internal force in the direction of or parallel to the centroidal axis of the beam 7. The internal force in the direction perpendicular to the centroidal axis
Problem 04.107 - Maximum load carrying capacity of a milled rod with known allowable stress A milling operation was used to remove a portion of a solid bar of square cross section. Knowing that a = 30 mm, d = 20 mm, and all = 54 MPa, determine the magnitude P of the largest force that can be safely applied at the centers of the ends of the bar. The magnitude P of the largest force that can be safely applied at the centers of the of the bar is KN.