Question 13 of 14 > - /5 View Policies Current Attempt in Progress Determine the coordinates of the mass center of the welded assembly of uniform slender rods made from the same bar stock. a 1.36 a Answers: (X, Y, Z) = ( i ) a i i II

Question 13 of 14 > - /5 View Policies Current Attempt in Progress Determine the coordinates of the mass center of the welded assembly of uniform slender rods made from the same bar stock. a 1.36 a Answers: (X, Y, Z) = ( i ) a i i II

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic: Stresses in Beams Instructions: Find the value of: y = C = A' = y' = I =
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.45 in. The outside diameter of the tube is D2 = 3.2 in. and its wall thickness is t2 = 0.140 in. Overall dimensions of the assembly are a = 42 in. and b = 6 in. The allowable shear stresses for the bronze and aluminum materials are 10700 psi and 8100 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 5.9°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
Give me right solution
Each of the three aluminum bars shown is to be twisted through an angle of 2.5°. Knowing that b=30 mm, Tall = 50 MPa, and G = 27 GPa, determine the shortest allowable length of each bar. Refer to Table 3.1. (a) (b) (c) 1.2h The shortest allowable length of bar (a) is The shortest allowable length of bar (b) is The shortest allowable length of bar (c) is mm. mm. mm.
Question 28 An A36 angle bar is used as a tension member connected on both legs with 18 mm. Given that s = 74 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. |40 50 L6x 3½x% 56 62.5 Ag = 1,852 mm2 t = 8 mm
Two forces of magnitude TA = 6159 kips and TC = 7180 kips are applied as shown to a welded connection. Knowing that the connection is in equilibrium and angle X is 43.9°, determine the magnitude (kips) of TB . Round off only on the final answer
A steel column is supported at the top by two steel rods so as to prevent movement at the top in the x-direction and the y-direction as shown. The column in this case is assumed to be fixed at the bottom and free to rotate but not translate at the top (pin support in x and y directions). If the steel rod along x-x fails (snaps). In this case, the recommended value of Kx for this column should be equal to:
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
Y Suppose that P = 250 lb. (Figure 1) Figure T T301-381-38- W 481 46 Part C FBC = Part D Submit Request Answer FBD= Part E FCD= Submit Part F FCE= Submit Determine the force in member of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compres the case of tension. Part G FDE= Part H - ΑΣΦ It vec Determine the force in member BD of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compressi the case of tension. FDF= 17 ΑΣΦ Submit Part I 1 of 1 > Request Answer Submit Request Answer FEF= ΓΙ ΑΣΦ 11 Eved Submit - Η ΑΣΦΙ Request Answer Determine the force in member CD of the truss.. Express your answer in pounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. -- ΑΣΦ Ivec Request Answer 17 ΑΣΦ 4 Part A 5 Request Answer it vec Determine the force in member AB of the truss Express your answer in pounds to…
a) For the solid section shown in Figure Q1, determine dimensions a, b and c. b) Determine the centroid position (x, y) for the solid section shown in Figure Q1 relative to the origin O on the x-y axes. Clearly show the breakdown of the section into areas used in your calculations. y 85 mm 53 mm b 25 mm 157° 25 mm 65 mm Figure Q1 (Not to scale) X
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.91 in2, A? = 0.31 in2, P1 = 81 kips, P2 = 47 kips, P3 - 31 kips and E = 29x106 psi %3D %3D Your final answer should have three decimal places A1 A2 B. D' P3 P1 P2 -/- --16 in 12 in. 12 in.
1- Calculate maximum deflection of the beams. 2- Check the suitability of the section assuming the code limitation of L/240. 3- If maximum deflection doesn’t meet the code requirement, propose your solution. Steel: Section properties: I=366,000,000 mm4, E=2*(10)5 N/mm2