Consider the girder and the moving loads shown in (Figure 1). Suppose that P = 80 kN. Figure 1 A 6m C 10 m 60 kN 30 kN < 1 of 1 30 kN m Part A -Determine the maximum live bending moment at C caused by the moving loads. Follow the sign convention Express your answer to three significant figures and include the appropriate units. (Mc)max= 710 Submit μA Provide Feedback CE ? kN m Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining

Consider the girder and the moving loads shown in (Figure 1). Suppose that P = 80 kN. Figure 1 A 6m C 10 m 60 kN 30 kN < 1 of 1 30 kN m Part A -Determine the maximum live bending moment at C caused by the moving loads. Follow the sign convention Express your answer to three significant figures and include the appropriate units. (Mc)max= 710 Submit μA Provide Feedback CE ? kN m Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the truss shown in the figure, estimate the horizontal displacement at joint H. The area (A) and the modulus of elasticity (E) of each bar is 0.5 in2 and 29000 ksi, respectively. Summarize your results in the following order. Member AB BC CD DE EF FG GH AH BH CH CG CF DF T 12 ft 2k B G C D 10 ft-10 ft- 10 ft-10 ft
Help me figure out the problem. Asking for the moment diagram? and then, Show the value of x knowing you have the shear diagram. Again find the moment diagram and the value of your x. Show complete solution and box the final answer and write on a paper.
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
Please send me the question in 30 minutes it's very urgent plz
Beam ABCD carries a concentrated load and uniformly distributed load as shown below. Draw the shear and moment diagram of the given beam. Show your solution.
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
SHOW THE DIAGRAM AND YOUR COMPLETE SOLUTION: A statically determinate beam is loaded as shown in the figure below. Determine the following: 1. Determine the shear and moment 5m from point A X A OXDC 30 KN.m 1.5 m Im B 1.5 m C L=6m 10 KN internal hinged 1.5 m 1.5 m ////// E
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Please answer only number 1 with complete solution (all computations must be 4 decimal places)
USE ALL DECIMAL PLACES IN SOLUTIONS AND ROUND OFF YOUR ANSWERS TO NEAREST WHOLE NUMBER. INPUT NUMERICAL VALUE ONLY.
Part A The beam is subjected to a uniform dead load of 1.4 kN/m and a single live load of F = 35 kN . Assume A is a pin, and B is a roller. Follow the sign convention. (Figure 1) Determine the maximum bending moment created by these loads at C. Express your answer to three significant figures and include the appropriate units. (Mc)max = 130 kN-m Submit Previous Answers Correct Correct answer is shown. Your answer 130.2 kN.m was either rounded differently or required for this part. Part B Determine the maximum positive shear at C. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 (Vc)max = Value Units 6 m 6 m Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining