Part AThe beam is subjected to a uniform dead load of1.4 kN/m and a single live load of F = 35 kN . AssumeA is a pin, and B is a roller. Follow the sign convention.(Figure 1)Determine the maximum bending moment created by these loads at C.Express your answer to three significant figures and include the appropriate units.(Mc)max = 130 kN-mSubmitPrevious AnswersCorrectCorrect answer is shown. Your answer 130.2 kN.m was either rounded differently orrequired for this part.Part BDetermine the maximum positive shear at C.Express your answer to three significant figures and include the appropriate units.Figure1 of 1(Vc)max =ValueUnits6 m6 mSubmitPrevious Answers Request AnswerX Incorrect; Try Again; 3 attempts remaining

Given:- The magnitude of the uniform dead load = 1.4 kN/m The magnitude of the single live load F =…

Part A The beam is subjected to a uniform dead load of 1.4 kN/m and a single live load of F = 35 kN . Assume A is a pin, and B is a roller. Follow the sign convention. (Figure 1) Determine the maximum bending moment created by these loads at C. Express your answer to three significant figures and include the appropriate units. (Mc)max = 130 kN-m Submit Previous Answers v Correct Correct answer is shown. Your answer 130.2 kN-m was either rounded differently required for this part. Part B Determine the maximum positive shear at C. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 HA ? (Vc)max = Value Units 6 m 6 m Submit Previous Answers Request Answer B X Incorrect; Try Again; 3 attempts remaining

Part A The beam is subjected to a uniform dead load of 1.4 kN/m and a single live load of F = 35 kN . Assume A is a pin, and B is a roller. Follow the sign convention. (Figure 1) Determine the maximum bending moment created by these loads at C. Express your answer to three significant figures and include the appropriate units. (Mc)max = 130 kN-m Submit Previous Answers v Correct Correct answer is shown. Your answer 130.2 kN-m was either rounded differently required for this part. Part B Determine the maximum positive shear at C. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 HA ? (Vc)max = Value Units 6 m 6 m Submit Previous Answers Request Answer B X Incorrect; Try Again; 3 attempts remaining

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need ans very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
27) Calculate the nominal moment strength of a reinforced concrete beam 210 mm x 470 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 25 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1850 in.4]. For the loading shown, determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 180 kip·ft, P = 25 kips, LAB = 7.3 ft, LBC = 11 ft.
The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm and Tensile Strength 210 MPa and Modulus of Elasticity 2x105 It is MPa. Since a load of 640 kg is hung on the D end of the system; For BC bar: a) Tensile stress, b) Safety coefficient, c) Calculate the length change amount.
Topic: TORQUE
As shown in figure, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G=42 GPa. Compute the maximum shearing stress in each spring using approximate equation. Steel ww 1 m Steel 50 kg 2m Phosphor Bronze
Stress Analysis of Trusses using method of sections. pls answer within 30 mins
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
Consider the timber beam shown below. The beam is made out of southern yellow pine, with an allowable bending stress of ?all= 2700 psi. The modulus of elasticity is E = 2,400 ksi. The maximum allowable deflection in the beam is 0.25 inches. A 1.5 kip/ft 6 ft 4 in. h B (a) What are the boundary conditions for this beam? (b) Determine the equation for the moment diagram using statics. (c) Determine the depth of the beam necessary to meet the allowable bending stress requirement.
Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210 GPa, E=110 GPa. All data in the Table below. Find: 1. Distance of the load (P) from the bronze wire. 2. Stresses developed in steel and brass wires. - Bronze Wire 250 cm Distance Steel wire Dia Dia Distance P (N) (steel) Сopper between two wires (mm) mm mm 26 35 850 8000
The 22-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 1 A of 1 600 mm B 400 mm 50 kN 50 kN C 40 kN MILA Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. 1 dc = Submit μÅ Value Units My Answers Give Up ?
Please answer correctly. Please I need this ASAP. thank you Note: The tolerance is ± 1 in the third significant digit