For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6

Q: y M 0.4 m/ 45 0.6 m 0.4 m For the above diagram, there are smooth journal bearings at supports A, B…

A: The value of force is The moment applied is The distance y is

Q: Solve the statics problem shown here by calculating the X-direction and Y-direction forces at points…

A:

Q: The frame in the figure is a counter-balance scale used for decades to offer products. Calculate the…

A: Given data, The distance of EFG is 350 mm. Value of b= 200 mm x varies from 10 mm to 400 mm. Mass of…

Q: Q1/ A brake shoe is applied to a drum by a lever AB which is pivoted at a fixed point A and rigidly…

A:

Q: A cast iron flywheel is rotated at a speed of 1200 rpm and having a mean rim radius of 1 foot. If…

A:

Q: The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one…

A: Given data:find:The maximum force

Q: Consider the four bar suspension linkage shown describing the figure. Use the given dimensions from…

A: take axis as shown in fig, B=W1,h1=5.9,8.1 E=w1+W2+W3+W4+W5, h3E=5.9+4.2+6.8+4.6+7.6, 14.8E=29.1,…

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A:

Q: also find ax and ay The rod is supported by smooth journal bearings at A, B. and Cand is subjected…

A:

Q: If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the…

A: Given data:find:Force resisted by piston F2

Q: urning moment 1mm = 60 Nm: crank angle, 1 mm = 1° . The turning moment shows the maximum energy that…

A:

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

A:

Q: a) Calculate the matrix of minors of S. b) Calculate the matrix of cofactors of S (name it H) c)…

A: To solve the problem, we first need to draw the free-body diagram of the truss and label all the…

Q: For the same question, the Impeller hub will be pressed onto the taper shaft with the Nut. How much…

A: given data; ⇒engine power(P)=27kw                        =27*103w⇒speed (n)=1684rpm⇒conical…

Q: pls explain to me step by step and pls dont skip any steps i will rate your answer immediately…

A: given data as per question force to be generated = 500 N dimension of a1 =100 mm dimension of a2…

Q: In the figure, a climber with a weight of 390 N is held by a belay rope connected to her climbing…

A: Given Data The weight of the climber is: w=390 N The angle at the toe is: θ=45° The angle at the…

Q: Q2/ In the nucleus pulposus of an intervertebral disc, the compressive load is 1.5 times the…

A: Given data: M=90 kgm=50 kg Need to determine the compressive loads on the nucleus pulposus and…

Q: A belt sander, shown in the figure below, weighs 11.19 lb and has a belt speed of 698 ft/min. A…

A: Given,A belt sander, weighs 11.19 lb and has a belt speed of 698 ft/min. A downward force of 13.51…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.