Consider the total hip joint prosthesis shown. The geometric parameters of the prosthesis are such that 11 = 50 mm, 12 = 100 mm, 1 = 450 and 2 = 90. Assume that when standing symmetrically on both feet, a joint reaction force of F = 400N is acting at the femoral head due to the body weight of the patient.

Consider the total hip joint prosthesis shown. The geometric parameters of the prosthesis are such that 11 = 50 mm, 12 = 100 mm, 1 = 450 and 2 = 90. Assume that when standing symmetrically on both feet, a joint reaction force of F = 400N is acting at the femoral head due to the body weight of the patient.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Similar questions

For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body weight acts through the tibia. The Achilles Tendon makes an angle (0) of 8° with the vertical and for this foot x1 is 6.2 cm and x2 is 12.3 cm. Calf Muscle Tibia Achilles Tendon Calculate the tension (T) in the Achilles Tendon if a 70 kg man stands on the toes of both feet. Using the values in this example what is the mechanical advantage for this lever and describe what that means in terms of the efficiency of the lever.
Needs Complete typed solution with 100 % accuracy.
The 300kn sphere is supported by a pull p and a 200kn weight passing over a frictionless pulley. If a=30°. Computer the value of p and tangent.
300 lb NOT TO SCALE B. E D 4 ft 650 lb · ft 3 ft 2 ft -2 ft→ The pin at point C fits into a smooth slot cut into member AC. Since there is no friction between the pin and the slot, the force there is normal to the slot. For component directions, use x positive to the right and y positive upward.
The car shown in the figure below has a mass of 1673 kg. The coefficient of static friction between the rubber tires and the pavement is 0.6. Determine the maximum incline e [degrees] that the car can drive up if it has rear-wheel drive. 0.85 m 1.2 m 1.7 m Answer: 18.87 Calculate the normal reaction force at the rear wheels for the condition of rear-wheel drive in N. Answer:
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
For the spring assemblage shown below, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 12.5 mm in the positive x direction because of the force F3 and k1 k2 175 kN/m.