I just need help with part D, thanks Learning Goal:A centroid is an object's geometric center. For an object of uniform composition, its centroid is also itscenter of mass. Often the centroid of a complex composite body is found by, first, cutting the body intoregular shaped segments, and then by calculating the weighted average of the segments' centroids.Anobject is made from a uniform piece of sheet metal. The object has dimensions of a = 1.45 ft, where a isthe diameter of the semi-circle,b= 3.24 ft, and c = 2.10 ft. A hole with diameter d = 0.500 ft is centeredat (1.13, 0.725).Figure4.00 in1.25 in2 of 2 >I=SubmitPart CFind y, the y-coordinate of the body's centroid. (Figure 1)Express your answer numerically in feet to three significant figures.► View Available Hint(s)——| ΑΣΦ |y =SubmitPart DZ =SubmitΠΙΑΣΦΗPart E Complete previous part(s)Part F Complete previous part(s)Provide Feedbackvec ^A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. (Figure 2) Assume that the scoop of ice cream is a sphere with radius r= 1.30in that is placed into a 4.00 in tall cone. The interior heightof the cone is 3.60 in. The cone has an exterior radius of 1.25 in and an interior radius of 1.10 in. The scoop of ice cream sits on the cone's interior radius and extends into the cone some distance. Find the centroid for the cone (the scoop of icecream and the cone).Express your answer numerically in inches to three significant figures.► View Available Hint(s)OEvec ^?ft?ftinNext >

gure 4.00 in 1.25 in < 2012 > A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. (Figure 2) Assume that the scoop of ice cream is a sphere with radius r=1.30in that is placed into a 4.00 in tall cone. The interior height of the cone is 3.60 in. The cone has an exterior radius of 1.25 in and an interior radius of 1.10 in. The scoop of ice cream sits on the cone's interior radius and extends into the cone some distance. Find the centroid for the cone (the scoop of ice cream and the cone) Express your answer numerically in inches to three significant figures. ▸ View Available Hint(s) E- Submit Part E Complete previous part(s) Part F Complete previous part(s) + CI?

gure 4.00 in 1.25 in < 2012 > A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. (Figure 2) Assume that the scoop of ice cream is a sphere with radius r=1.30in that is placed into a 4.00 in tall cone. The interior height of the cone is 3.60 in. The cone has an exterior radius of 1.25 in and an interior radius of 1.10 in. The scoop of ice cream sits on the cone's interior radius and extends into the cone some distance. Find the centroid for the cone (the scoop of ice cream and the cone) Express your answer numerically in inches to three significant figures. ▸ View Available Hint(s) E- Submit Part E Complete previous part(s) Part F Complete previous part(s) + CI?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Subparts 1, 2, and 3.
where did you guys get the area from?
500mm 30mg 40mm LBC 40mm LAB
Task 1: Produce a report by applying the concepts of engineering materials relating to a tricycle as shown in Figure 1, with the following incorporated: 3. Choose the most appropriate material from your point of view that can be used to produce the item/product with reasons discussed. Figure 1: Tricycle
Project 7: In this project you were assigned to explore your mechanical design and system capabilities. Your manger asked you to prepare a technical research report to evaluate the effects of misalignment of shafts and the measures that are taken to prevent problems from occurring. The hiring committee asked you to deliver a short report showing your evaluation (no more than 600 words).
Problem- Cargo ships can cause a lot of air pollution.Solution- to use nuclear powered ships since they hold a lot of energy and can travel for long distances. How it will work is that it will need a nuclear reactor at the bottom of the boat to heat up the water and then turn it to electricity to power the boat. The boat will be made out of graphene which is a tough material to avoid any leaks in the boat. It will also contain many control rods because nuclear power is so powerful that it can create to much energy to handle. With control rods, you can slow down this process and keep it in a controlled manner. Since cargo ships are already is the ocean, there will be no need for any extra materials to make it work. -Do you think this will work? Why/Why not? -What do you think is wrong with it/ How can this be improved? Please send this to someone else I need to record 50 responses for a science project. Thank you!
Diagram: Given the hook-up drawing, list all the equipment, tools and materials that are needed in installation. INST. PIPING 1- *1 INST. PIPING
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…