Consider the four bar suspension linkage shown in the figure. Use the given dimensions from the tablebelow to write the position vector describing the lowest link and the position vector describingthe shock. Express each vector in Cartesian components and also as a magnitude and an angle (measuredcounterclockwise from an z-axis defined parallel to the ground and pointing right).h₂h₂hah₂AFkW,Bhas magnitude TBE =CCW from horizontal.CH-W₂W₁values for dimensions on the figure are given in the following table. Note the figure may not be to scale.variable value Variablehy8.1 in2₂h₂13.1 in201214.8 inW38.9 inW₁3.8 inWzhas magnitude TCH =Ccw from horizontal.Submit Questionvalue5.9 in4.2 in6.8 in4.6 in7.6 ininchesinches and points at an angle of3) incheshsinches and points at an angle ofh₂@080NC SA2013Michael Swanbomdegreesdegrees

take axis as shown in fig, B=W1,h1=5.9,8.1 E=w1+W2+W3+W4+W5, h3E=5.9+4.2+6.8+4.6+7.6, 14.8E=29.1,…

Consider the four bar suspension linkage shown describing the figure. Use the given dimensions from the table below to write the position vector describing the lowest link and the position vector the shock. Express each vector in Cartesian components and also as a magnitude and an angle (measured counterclockwise from an z-axis defined parallel to the ground and pointing right). 1₂ h₁ ↓ www hs -$* na h₂

Consider the four bar suspension linkage shown describing the figure. Use the given dimensions from the table below to write the position vector describing the lowest link and the position vector the shock. Express each vector in Cartesian components and also as a magnitude and an angle (measured counterclockwise from an z-axis defined parallel to the ground and pointing right). 1₂ h₁ ↓ www hs -$* na h₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Need help, round answers to 3 sig figs please
Solve correctly
In the kinematic chain shown below, the lengths of the vectors in inches are: r₁ = 6.8, r2 = 2.7, r3= 5.4, and r4 = 7.1. Based on the kinematic chain shown below, what is the angle of the coupler 03 in degrees rounded to one decimal place that makes 04 a maximum (Enter angle in the range of 0 to 360°)? 0₂ 0₂ Previous P3 10₂ 04 Type your answer... 14 B Next
Required information A model of a person's arm is used for ergonomics studies. Distances are rAB = 30 cm, BC = 28 cm, and rCD = 19 cm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y D C25° 30 Determine the position vector TAD and its magnitude rAD· The position vector TAD 1i)cm and the magnitude rAD is cm.
Q1/The figure below shows such an LSPB trajectory, where the maximum velocity V = 60 deg/sec. In this case, the times are given as t = 5 sec and t-30 sec. In addition, the joint angles in beginning and the ending q-20 deg and q;= 70 deg, respectively. For these required data, determine the following: 1- The position function and its profile. 2- The velocity function and its profile. 3- The acceleration function and its profile. 4- The function of jerk variable and what is the nature of jerk? 5- The position, velocity, and acceleration at tm=13 sec. 9A ty te 9 9. 9 0 t₁
Q1/ The figure below shows such an LSPB trajectory, where the maximum velocity V 60 deg/sec. In this case, the times are given as t.= 5 sec and t 30 sec. In addition, the joint angles in beginning and the ending q=20 deg and qf = 70 deg , respectively. For these required data , determine the following : 1- The position function and its profile. 2- The velocity function and its profile. 3- The acceleration function and its profile. 4- The function of jerk variable and what is the nature of jerk? 5- The position, velocity, and acceleration at tm-13 sec. te tm ty te ty t
Two cables AB and AC are acting on the pole with forces FAB=540N and FAC = 560N with parameters defining the attachment points shown in the table. We want to write the vector AB in cartesian vector form. C Y₂ parameters value units 540 560 5.5 4 3.5 FAB FAC L Z1 Y 72 4 4 Submit Question N N m m m m m A x + 247.123 Y₁ write the vector FAB in Cartensian Vector Notation. Round your final answers to 3 significant figures. FAB= 282.427 Z B xj+-388.337 N
The vector expressions for the position vectors for cables “AC” and “AD” are given by: rAC = -3i - j - 6k ft and rAD = 2i + 3j - 6k ft respectively. What is the length of cable “AD”?
what are the contents of the circled formula and what is it called? and what is the relationship between δp and δt, why are the solutions different in the following line? (arrows)