The following represents stress measured in the global coordinate system [10 (X1, X2, X3) as o = |20 L30 20 30] 40 50 50 60]

Q: conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism,…

A:

Q: Questions 8, 9 and 10 For the pipe assembly shown in the figure, if F = [6i + 18j 10k] Ib, determine…

A:

Q: LQ1], The motion of a particle is "defined the position coordinates : by [x = t" - 3t+t], where…

A: Given Data⇒ Motion of particle is defined by : X=t4-3t2+t t=3 s

Q: On drawing 31A063, how many flat, finished surfaces does the part contain?   All abbreviations are…

A: The basic graphical symbol used to indicate the surface texture is shown below. In order to obtain…

Q: Draw the isometric and orthographic ( top front side ) of the following sketch

A:

Q: E₁ = 200GP₁₁ A₁ = 200 mm ² A 1.45 [m] 2 A = 400 mm ² C T point A and point D lies 2.625 m from wall…

A:

Q: 2. Make a conclusion: In which case the measurement result is more accuracy. Result 1 XN123,84658…

A: Given data is related to metrology.

Q: A bar is pinned to ground at its O with the bar rotating clock-wise at a constant rate of…

A: Given: Ω=8.9[rad/s] Vp=9.7 [ft/s] h=4.7[ft] rA/O=1.2[ft] To find: J^ component of v¯A? J^ component…

Q: Match the following terminology to the proper description. direction cosines alpha beta gamma…

A: 1.Direction cosines:The cosines of the angles between vector and the three positive coordinate axes,…

Q: Questions 1, 2 and 3: For the pipe assembly shown in the figure, if F = [6i +18) -10k) Ib, determine…

A:

Q: Acceleration, a [m/s²] Number (0,ao) m/s Time, t [s] (t₁,ao) Given the above figure, where t₁ = 4s…

A:

Q: 1.1 s) The overall size of the system (i.e. the shell) is 5.8 inch ID and a 27-inch long tube…

A:

Q: A local camera station is tracking a UFO sighting in the evening sky. Find the velocity and…

A:

Q: The outside diameter of a hollow tube is 15 cm, and its cross-sectional area is 32 cm². What is the…

A: Given:  Do = 15  cm  A = 32 cm2 di = ?

Q: Given the following figure, what is the resultant force due to the distributed load? Units are taken…

A: In the given figure, force distribution diagram is shown. The force is a function of x. It is…

Q: What is the value of ybar from the 1-1 line [ Select] What is the value of centroidal MOI Ixx?…

A:

Q: On drawing 31A063, how many holes are specified?   All abbreviations are standard

A: A multi-view of drawing means that a graphical representation of a 3-D figure to 2-D drawing using…

Q: If a rock is thrown upward on the planet Mars with a velocity 8 m/s, its height in meters t seconds…

A: Given That: Velocity = 8 m/s y = 8t - 1.86t2

Q: A particle is subjected to the action of two forces: F1 = 4 i+ 7j+7 k [kN] and F2 = 5 i - 6 j - 5 k…

A:

Q: The temperature of an electrically heated pipe varies in the radial direction and is defined by the…

A:

Q: Determine whether the following equations are dimensionally homogeneous. f = m· a + c · v + k · x f…

A: The dimensions of various term used in the expression are as follows: m·a=kg·ms2=MLT-2 And…

Q: force 15[kN-m¹] 2m. ПА 2m 2m * 7x inclu ir a 25KN) Find location of the application of the posulions…

A:

Q: spring 2 and spring 3 in parallel

A: calculate the required stiffness of the spring

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.