The frame in the figure is a counter-balance scale used for decades to offer products. Calculate the maximum and minimum weight L that this balance can support if the EFG bar measures 350 mm, the distance b is 200 mm, x varies between 10-400 mm and the mass of the counterweight S = 200 grams

Q: The force F1 = 5 kN, F2= 5 kN, F3= 10 kN, F4 = 5 kN are acting on the structure shown. Determine the…

A: According to the given dataWe need to findThe tension in the force BC , BE and EF

Q: 900 lb 600 lb 4 ft +4ft 4 ft 3 ft B If the truss shown above is in static equilibrium as loaded,…

A:

Q: show all steps in detail, units and formulas please.

A:

Q: A sandwich board advertising sign is constructed as shown in the figure below. Hinge- 0.50m Chain…

A: Given Data: m=7.2 kg   To Find: (a) The tension in the chain. (b) Force exerted by each side on the…

Q: As shown, an L-shaped bar is supported by a pin at joint A. The bar's dimensions are aaa = 620 mmmm…

A: Introduction We shall compute the real orientation of the applied force at an angle in this…

Q: The arm in the figure below weighs 37.6 N. The force of gravity acting on the arm acts through point…

A: The weight of the arms act at A. Taking the moment of the forces about point O,

Q: For the truss shown, find the magnitude of the force F BE using the figure and the given data. F₁ =…

A:

Q: A floor hoist supports an engine of weight WE 2.9 kN. As illustrated in the figure below, the floor…

A: The value are .The weight of the engine is The angle is

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which…

A: Data given-  OA bar weight = 18 m  Theta = 60°

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a = 2 ft • b= 4 ft c= 1 ft then, what…

A: Consider the free body diagram of member AC, Here,

Q: Task 3: The sketched overhead crane carries the effective force F1 = 60 KN and the balancing load F2…

A: provide the specific functionality of the PLC program in the image without more contex

Q: The arm in the figure below weighs 38.0 N. The force of gravity acting on the arm acts through point…

A:

Q: The two bearings (B1) and (B2) are used to support a shaft as shown in the figure Using the data…

A:

Q: Set P₁ = 7 kN, P₂ = 8 kN . (Figure 1) Figure 4m B E 4m 4 m 6 m D

A:

Q: calculate the forces in AB and BC

A: The problem involves writing the forces in the members using Position Vectors and solving the…

Q: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

A: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

Q: Please answer with a complete solution. Thank you! Find the distance x (measured along AB) at which…

A:

Q: 1 m 1 m 30° b. 0.5 m 0.5 m b 1m -75 mm-

A: Given Data The mass of the drum is:m=20 kg The supported diamter of frame is :D=2mm Now draw the…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.