following data were obtained: - Surface area of diffusion = 33.4 cm2 - Original concentration = 1.7 mg/mL - The permeability coefficient = 3.85 x 10-6 cm/s a) Calculate the amount of drug that will permeate in 4.5 hours if the experiment was carried out under sink conditions. b) Is the system working under steady-state conditions? Explain.

following data were obtained: - Surface area of diffusion = 33.4 cm2 - Original concentration = 1.7 mg/mL - The permeability coefficient = 3.85 x 10-6 cm/s a) Calculate the amount of drug that will permeate in 4.5 hours if the experiment was carried out under sink conditions. b) Is the system working under steady-state conditions? Explain.

Biochemistry

9th Edition

ISBN:9781319114671

Author:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Publisher:Lubert Stryer, Jeremy M. Berg, John L. Tymoczko, Gregory J. Gatto Jr.

Chapter1: Biochemistry: An Evolving Science

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Your labmate forgot to use CBB-R250 in the process. Which of the following would most likely be the resulting gel?
List the mechanism and give several names of the following: Class I, Class II, Class III, and Class IV antiarrythmics.
When testing the tonicity of potato strips, why is the amount of wait time after adding the potato strip an important factor in the experiment a)the lower the concentration of solute in the solution more time is required for osmosis to occcur. b) the potato immediately absorbs water. the higher the concentration of solute in the solutiokn more tomes is required for osomis to occur d) the potato will spoil so you have to work quickly
Plate A = filter paper dipped into 5% solution of unknown Dye A %3D Plate B = filter paper dipped into 5% solution of unknown Dye B Both plates were incubated at 37°C. At the end of the 60 minute incubation period the diffusion rings for each dye were measured. The diffusion ring for Dye A = 40 mm. The diffusion ring for Dye B = 24 mm %3D Based on the results, which dye had the higher molecular weight? Explain your answer.
A) Consider membrane filtration. What is concentration polarization and why does it occur? B) What are the important parameters that affect the diffusivity in/across membranes and what do The they mean physically? C) Consider the Krogh Cylinder model. What is the physical meaning of the critical radiusand why does it occur?
What is an electrochemical gradient? What purpose does it serve?
Polymer nanoparticles, Microparticles and hydrogels have been developed for slow and sustained drug release for slow and sustained drug release application; mark all that apply below: 1)Drug release from hydrogels can be via (a) drug diffusion, (b) degradation of the polymeric matrix and (c) swelling 2) PLGA degrades to lactic acid and glycolic acid, which are not biocompatible 3) Drug release can be triggered through internal and external stimuli - I.e. by use of pH labile chemistries or external triggers 4) Burst release describes the initial faster release rates often observed in drug delivery system, which is then followed by sustained release 5) while burst release is observed with polymer nanoparticles, it is not observed from hydrogels
Give the IUPAC names of the following. Answer A, B, C and D. Thank you!
(e) Two ADP agonists (drugs) were also found to bind to platelets: 2-methylthio-ADP bound with a Kp of 7 µM and 2-(3-aminopropylthio)-ADP bound with a Kp of 200 µM. Can these drugs effectively compete with ADP for binding to platelets? Explain your answer.
Recall the power law equation Y = aXb. Which of the following statements is true? : a) a = 0.34 and b = 1 best describes homeotherms; a = 0.13 and b = 0.75 best describes poikilotherms b) a = 0.34 and b = 0.75 best describes poikilotherms; a = 0.13 and b = 0.75 best describes homeotherms c) a = 0.34 and b = 0.75 best describes homeotherms; a = 0.13 and b = 1 best describes poikilotherms d) a = 0.34 and b = 0.75 best describes homeotherms; a = 0.13 and b = 0.75 best describes poikilotherms
What is the principle behind the Diffusion experiment?
How many ml is needed to fill this prescription Gabapentin liquid 300mg/5ml 300 mg po TID x 30 days A) 90ml B) 450ml C) 300ml D) 150ml