+ Find the Plastic and Section Modulus of a A W14 x 34 with cover plate on each flange. The plate is 3/8 x 8 in. and draw. Use the given only if needed. Shape W14X34 T 11.625 ly 23.3 Sw1 17.6 A 10 gage 3.5 Sy 6.91 Qf 10 d 14 wt./ft. bf/(2*tf) 34 7.41 ry 1.53 tw 0.285 Qw 26.9 Zy 10.6 bf 6.75 h/tw 43.1 rts 1.8 tf 0.455 Ix 340 ho 13.5 k(des) k(det) 0.855 1.1875 Sx 48.6 J 0.569 rx 5.83 Cw 1070 k1 0.75 Zx 54.6 Wno 22.9

+ Find the Plastic and Section Modulus of a A W14 x 34 with cover plate on each flange. The plate is 3/8 x 8 in. and draw. Use the given only if needed. Shape W14X34 T 11.625 ly 23.3 Sw1 17.6 A 10 gage 3.5 Sy 6.91 Qf 10 d 14 wt./ft. bf/(2*tf) 34 7.41 ry 1.53 tw 0.285 Qw 26.9 Zy 10.6 bf 6.75 h/tw 43.1 rts 1.8 tf 0.455 Ix 340 ho 13.5 k(des) k(det) 0.855 1.1875 Sx 48.6 J 0.569 rx 5.83 Cw 1070 k1 0.75 Zx 54.6 Wno 22.9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.9-9 A column cross section is built up from four L5 x 5x 4, as shown in Figure P4.9-9. The angles are held in position by lacing bars, whose primary function is to hold the angles in position. The lacing is not con- sidered to contribute to the cross-sectional area, which is why it is shown by dashed lines. AISC Section E6 covers the design of lacing. The ef- fective length is 30 feet with respect to both axes, and A572 Grade 50 steel is used. Investigate flexural buckling only (no torsional buckling) and compute a. the design strength for LRFD. b. the allowable strength for ASD. -1'-6"- 1'-6" 1'-6" FIGURE P4.9-9 Just LRFD and check for local buckling
SN = 11
Ultimate axial force capacity of the section _____ kN
6.(b) A column is made of 4 os. SA 100 x 100 x 10 as shown. The effective length of column is 6 m The lacing of column consists of 60 mm 10 mm flat bars arranged in a single laced system by bolts and inclined at an angle of 45°. Determine the factored load on the column and check the local buckling of column angles. [ISA 100 x 100 x 10 A 1903 mm², Ixx Ivy 177 x 104 mm* Cxx 28.4 mm]. Assume gauge length - 55 mm and r = 19.4 mm. Cyy= = =
An A36 axially loaded 20mm thick tension member is connected to a gusset plate using5pcs 18mm diameter rivets arranged as shown. Use Fy= 248MPa & Fu=400MPa for thesteel plates. Given a=56mm, b=88mm, c=95mm, x=99mm, y=85mm and z=58mm. Calculate the allowable tensile strength (ASD) in KN based on Gross SectionYielding (GSY). Express your answer in 2 decimal places.
Fast okk
An unsymmetrical flexural member consists of a %x14 in. top flange, a %10 in. bottom flange, and a ¾×20 in. web. (a) Determine the distance y from the top of the shape to the horizontal plastic neutral axis (P.N.A.). (b) If A572 Grade 50 steel is used, what is the plastic moment Mp for the horizontal P.N.A.? (c) Compute Zy, the plastic section modulus with respect to the minor principal axis. (d) Calculate the ratio of Z,/S,. (Note: S, is the (elastic) section modulus with respect to the minor principal axis.
with solution
3. Given the modified steel section (added plate) shown in the diagram below, locate the centroid of the section relative to the bottom of the beam. Calculate the area moment of inertia of the modified section about the x axis through the combined centroid. Note that the section properties of the W14x82 are given in Appendix Table A3 of the textbook (Onouye). -2x8 STEEL PLÁTE CENTERED
Use method of members im solving. Please DRAW COMPLETE FBD
Q3) The beam shown in Figure below has lateral support at the ends only. The concentrated loads are live loads. Use A992 steel and select a W shape. (Do not check deflections. Use C-1). 23 k 25 k ttst
11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? A350 Pa CS with 6.5T5MP C. 140 Pa B. A D. 965 MPa Determine the diameter required using the actual shear stress. B. 8.53 mim C. 12.06 mm A. 13.49 mm D. 19.07 mm