Fasten the header cover of the cylinder with an inner diameter of 400 mm and an internal pressure of 2 MPa with 16 bolts. 1 Additional load applied to one bolt by internal pressure (P) 2 Assuming that the total fastening force per bolt (Qb) is twice the load (P) applied to one additional bolt by internal pressure, the initial fastening force (Q0) to be applied to the bolt initially 3 Assuming that only tensile force (Qb) is applied to the bolt, the bolt diameter (d1)

Fasten the header cover of the cylinder with an inner diameter of 400 mm and an internal pressure of 2 MPa with 16 bolts. 1 Additional load applied to one bolt by internal pressure (P) 2 Assuming that the total fastening force per bolt (Qb) is twice the load (P) applied to one additional bolt by internal pressure, the initial fastening force (Q0) to be applied to the bolt initially 3 Assuming that only tensile force (Qb) is applied to the bolt, the bolt diameter (d1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The five-bolt connection must support an applied load of P= 1700 lb. If the average shear stress in the bolts must be limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. [coc00 Answer: dmin = in.
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
Problem 4.81 The 60-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20° C. (Figure 1) Figure 1 of 1 -11 100 mm 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T2 = 130°C. Express your answer to three significant figures and include the appropriate units. F= Submit HA Value Units My Answers Give Up ? Provide Feedback Continue
The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Design the most economical shank diameter and thickness of the nut.
For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to 220 MPa. Determine the maximum load P that may be applied to the connection. O 164 KN 149 kN O 94 KN O 109 kN O 122 kN
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. Q # 3 15KN Rotating shaft Pillow block Metric (ISO) screw (c) Determine the stiffness of the 15 members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted. Steel 1cm Som Grey Cast Iron CLO-3, PLO-2
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
If the design tensile strength Phi Pn of a tension member is controlled by rupture failure. Which of the following actions will NOT increase its capacity? using welds instead of bolts using larger cross section of the member increasing strength of steel using thicker gusset plate
A rolled l-shaped beam is connected to a steel girder by 4-25mm bolts as shown. Determine the maximum end reaction that the beam can resist. (tw=15mm, Fy=248 MPa, Fu=400MPA) 60 mm 25-mm bolts- 3 @ 80 mm W 14 × 211 2 - 100 mm angle leg 60 mm
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm